Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+VI\s+plus\s+receiver\s+problem\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+VI\s+plus\s+receiver\s+problem\s*$/: 7 ]

Total 7 documents matching your query.

1. [TenTec] Omni VI plus receiver problem (score: 1): Author: w5ot@aol.com; Date: Sat, 27 Jun 2009 00:17:34 -0400; My receiver emits a wind tunnel like rushing sound and tone on all frequencies when rf gain is at or near max.? it just started doing this after working flawlessly.? any suggestions would be apprecia; /archives//html/TenTec/2009-06/msg00123.html (6,890 bytes)
2. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: Richards <jruing@ameritech.net>; Date: Sat, 27 Jun 2009 06:40:02 -0400; Whenever I get anything odd, I reboot the rig and do a refresh of the software, Didja try that? What happens if you lower RF gain? Does it act right if you do? == JR == == ___________________________; /archives//html/TenTec/2009-06/msg00126.html (7,011 bytes)
3. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: Jim Goudie <JAGoudie@comcast.net>; Date: Fri, 26 Jun 2009 19:06:28 -0400; Hi! Is the Pass-band tuning operating normally? I had some flaky problems that were caused by dirty connectors between boards & controls (display and PBT in particular). Someone on the list recommend; /archives//html/TenTec/2009-06/msg00128.html (8,596 bytes)
4. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: "Dr. Gerald N. Johnson" <geraldj@weather.net>; Date: Sat, 27 Jun 2009 08:28:05 -0600; Contact and switch cleaning is MUCH more effective with a contact cleaner like DeoxIT from Cramolin than by mere abrasion. It just takes a fraction of a drop per contact and its not a good idea to so; /archives//html/TenTec/2009-06/msg00129.html (8,369 bytes)
5. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: w5ot@aol.com; Date: Sat, 27 Jun 2009 11:55:11 -0400; Yes, the problem only occurs near the rf gain maximum. Whenever I get anything odd, I reboot the rig and do a refresh of the software, Didja try that? What happens if you lower RF gain? Does it act r; /archives//html/TenTec/2009-06/msg00130.html (8,182 bytes)
6. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: "David & Chris Drake" <drakes@psci.net>; Date: Mon, 29 Jun 2009 09:06:36 -0400; Suggested steps: 1) check all wiring harness connectors on the IF board, the IF/AF board, next go to the lower pot board and inspect the af-rf pot closely. Insure you do not have any broken solder jo; /archives//html/TenTec/2009-06/msg00138.html (10,199 bytes)
7. Re: [TenTec] Omni VI plus receiver problem (score: 1): Author: Stuart Rohre <rohre@arlut.utexas.edu>; Date: Mon, 29 Jun 2009 16:48:54 -0500; I would call Ten Tec service after step 1 and before step 2. This may be a known problem with them, and would save you the time of a complete alignment. Rarely does an alignment need to be done if th; /archives//html/TenTec/2009-06/msg00151.html (8,289 bytes)

Current List: 1 - 7
Page: [1]