- 1. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: jdvoracek@vvm.com (John Dvoracek)
- Date: Sat, 7 Aug 1999 11:18:11 -0500
- How tight is the tuning encoder on an omni vi+? I have no tension on my tuning knob; in fact I have moved the knob out slightly on the encoder shaft so there is complete clearance between the front p
- /archives//html/TenTec/1999-08/msg00126.html (8,234 bytes)
- 2. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: n4lq@iglou.com (Steve Ellington N4LQ)
- Date: Sat, 7 Aug 1999 16:11:44 -0400
- There's a local here with a 6+. His encoder feels rather stiff in spite of adjustments but the ones I spun at Dayton felt smooth and easy to turn. Who knows why? Steve N4LQ -- Original Message -- Fro
- /archives//html/TenTec/1999-08/msg00129.html (9,279 bytes)
- 3. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: k4aal@jackatak.theporch.com (Ariel Elam)
- Date: Sat, 07 Aug 1999 23:02:24 -0500
- Hi to All--I have had to replace the tuning encoder on my VI+. Cost $43.98 shipped from TT. Check the rit encoderfor drag. I believe they are the same devices, as TT adaised me to interchange their c
- /archives//html/TenTec/1999-08/msg00135.html (9,417 bytes)
- 4. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: k7kj@teleport.com (Greg Hodsdon)
- Date: Sat, 07 Aug 1999 22:03:51 -0700
- I have had to replace two encoders. The first was on a new Omni 6+ purchased last September and more recently on a 301 kit. Both were replaced under warranty. The drag on the encoder tends to loosen
- /archives//html/TenTec/1999-08/msg00136.html (7,990 bytes)
- 5. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: wb0cff@hotmail.com (Carl R. Gansen)
- Date: Tue, 10 Aug 1999 14:35:37 PDT
- My Omni 6 came back from the OPT 3 upgrade considerably tighter than when it went in. Loosening the hex nut on the encoder just behind the knob made it eadier to turn again. I suspect that every now
- /archives//html/TenTec/1999-08/msg00148.html (10,951 bytes)
- 6. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: k4beh@juno.com (k4beh@juno.com)
- Date: Tue, 10 Aug 1999 18:17:05 -0400
- Hi TenTekkies, I haven't sent a rig in for any repair that would have required removal of the front panel/encoder, but I had to replace the encoder on either my Delta II or Paragon several years ago
- /archives//html/TenTec/1999-08/msg00149.html (13,239 bytes)
- 7. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: wb0cff@hotmail.com (Carl R. Gansen)
- Date: Tue, 10 Aug 1999 17:16:14 PDT
- Thanks for the input Pat; I have read the operators manual and was familiar with the operation of the drag. In my case I had moved the knob out as a step in the troubleshooting process so that the dr
- /archives//html/TenTec/1999-08/msg00150.html (9,778 bytes)
- 8. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: n1eu@yahoo.com (N1EU)
- Date: Tue, 10 Aug 1999 18:52:09 -0700 (PDT)
- Pardon the dumb question (duh), but could someone please point me to where in the Omni manual the tuning drag adjustment is described? Tnx & 73, Barry N1EU ___________________________________________
- /archives//html/TenTec/1999-08/msg00152.html (8,038 bytes)
- 9. [TenTec] Omni vi+ optical encoder (score: 1)
- Author: wb0cff@hotmail.com (Carl R. Gansen)
- Date: Thu, 12 Aug 1999 12:37:24 PDT
- It is section 2-5 of Chapter in my rev. of the manual. I think it's actually worthwhile to remove the knob and watch how the drag adjustment works. You quickly get a feel for how to take best advanta
- /archives//html/TenTec/1999-08/msg00175.html (9,305 bytes)
This search system is powered by
Namazu