- 1. [TenTec] Clean Eagle (score: 1)
- Author: Michael Goltz <whomike@gmail.com>
- Date: Fri, 3 Jul 2020 12:33:53 -0400
- Hello! I am curious. Is your TT 238 for a possible trade a model C ? Please reply to N8DNA@ARRL.net Thanks! Mike. N8DNA _______________________________________________ TenTec mailing list TenTec@cont
- /archives//html/TenTec/2020-07/msg00002.html (9,244 bytes)
- 2. [TenTec] Orion II No Output 10M and 12M (score: 1)
- Author: Frank Sweeney <k9ic.ars@gmail.com>
- Date: Sun, 5 Jul 2020 20:21:45 -0400
- I have no output on 10M and 12M Any thoughts on what to check 1st? thanks Frank K9IC _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.
- /archives//html/TenTec/2020-07/msg00003.html (7,298 bytes)
- 3. Re: [TenTec] Orion II No Output 10M and 12M (score: 1)
- Author: Rodney Dewald via TenTec <tentec@contesting.com>
- Date: Sun, 5 Jul 2020 20:23:37 -0400
- Relays Sent from Mail for Windows 10 I have no output on 10M and 12M Any thoughts on what to check 1st? thanks Frank K9IC _______________________________________________ TenTec mailing list TenTec@co
- /archives//html/TenTec/2020-07/msg00004.html (7,862 bytes)
- 4. Re: [TenTec] Orion II No Output 10M and 12M (score: 1)
- Author: Bob McGraw K4TAX <rmcgraw@blomand.net>
- Date: Sun, 5 Jul 2020 19:37:28 -0500
- Relays on the Low Pass Filter board may have an open coil. 10 & 12 share the same filter section. Two relays per filter section, coils in parallel. Also I recall a small RFC in series with the coil.
- /archives//html/TenTec/2020-07/msg00005.html (8,306 bytes)
- 5. Re: [TenTec] Orion II No Output 10M and 12M (score: 1)
- Author: Frank Sweeney <k9ic.ars@gmail.com>
- Date: Mon, 6 Jul 2020 13:13:57 -0400
- I am running a bit blind with no schematic. Is the 10M LPF the smallest inductors on the board (air wound) thanks Frank _______________________________________________ TenTec mailing list TenTec@cont
- /archives//html/TenTec/2020-07/msg00006.html (7,374 bytes)
- 6. Re: [TenTec] TenTec Digest, Vol 211, Issue 4 (score: 1)
- Author: Onno PA1AP <pa1ap@nextchallenge.net>
- Date: Mon, 6 Jul 2020 21:37:25 +0200
- When transmitting on 10/12 do you see the same current being drawn as applicable for other bands? The pwr / swr detection follows the bandpass filters. If it's not detecting pwr voltage it will just
- /archives//html/TenTec/2020-07/msg00008.html (12,840 bytes)
- 7. [TenTec] HF Xcvr, cables, and more FS (score: 1)
- Author: "Ken, W8EK" <kenw8ek@gmail.com>
- Date: Tue, 7 Jul 2020 09:52:17 -0400
- TenTec Delta II Model 536 HF Transceiver, cables, boxes, and more For Sale: . Ten-Tec Delta II model 536 Transceiver The Delta II is a synthesized hf transceiver with general coverage receive and 100
- /archives//html/TenTec/2020-07/msg00010.html (8,938 bytes)
- 8. Re: [TenTec] Orion II No Output 10M and 12M (score: 1)
- Author: Frank Sweeney <k9ic.ars@gmail.com>
- Date: Tue, 7 Jul 2020 15:17:03 -0400
- Issued resolved K1 (10M) one of two relays has high contact resistance. Relay has been replaced and all works as it should. Thanks everyone for your input 73, Frank K9IC _____________________________
- /archives//html/TenTec/2020-07/msg00011.html (8,085 bytes)
This search system is powered by
Namazu