Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Orion\s+II\s+won\'t\s+flash\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Orion\s+II\s+won\'t\s+flash\s*$/: 11 ]

Total 11 documents matching your query.

1. [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Sun, 4 Jan 2015 10:53:06 +0000; Has anybody else ran across this issue or have some informed suggestions? My logging software communicates fine with my Orion II but the latest Updater (v4.15) reports communincation failure over the; /archives//html/TenTec/2015-01/msg00012.html (7,196 bytes)
2. Re: [TenTec] Orion II won't flash (score: 1): Author: "John T. Fleming" <john@w3gqj.net>; Date: Sun, 4 Jan 2015 07:38:11 -0500; Barry, Have you tried rebooting the computer? 73, John Has anybody else ran across this issue or have some informed suggestions? My logging software communicates fine with my Orion II but the latest; /archives//html/TenTec/2015-01/msg00013.html (8,027 bytes)
3. Re: [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Sun, 4 Jan 2015 12:44:22 +0000; Yes, no change. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec; /archives//html/TenTec/2015-01/msg00014.html (8,399 bytes)
4. Re: [TenTec] Orion II won't flash (score: 1): Author: Carl Moreschi <n4py3@earthlink.net>; Date: Sun, 04 Jan 2015 07:55:57 -0500; The oscillator in the Orion for the serial port that causes it run to run at 57600 baud may have drifted off frequency just enough to cause an error when lots of data is being sent to it. I do rememb; /archives//html/TenTec/2015-01/msg00015.html (9,280 bytes)
5. Re: [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Sun, 4 Jan 2015 13:58:01 +0000; Thanks Carl, but the updater allows you to only select the COM port. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/list; /archives//html/TenTec/2015-01/msg00016.html (11,073 bytes)
6. Re: [TenTec] Orion II won't flash (score: 1): Author: "Martin Sole (HS0ZED)" <martin@hs0zed.com>; Date: Sun, 04 Jan 2015 21:22:06 +0700; I recall 2 issues with my 565 Orion that caused updating problems, battery and the 1uF caps around the MAX232 chip on the front panel module. O2 may be different. The oscillator in the Orion for the; /archives//html/TenTec/2015-01/msg00017.html (11,226 bytes)
7. Re: [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Sun, 4 Jan 2015 14:42:10 +0000; Thanks Martin. The battery was replaced by the factory in Feb 2014 but I might try replacing it again as a last resort if no better ideas come up. 73, Barry N1EU _____________________________________; /archives//html/TenTec/2015-01/msg00018.html (12,650 bytes)
8. Re: [TenTec] Orion II won't flash (score: 1): Author: Carl Moreschi <n4py3@earthlink.net>; Date: Sun, 04 Jan 2015 09:56:58 -0500; I would think the caps might be a better one to try. The max232 area sounds like the problem. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com 73, Barry N1EU I recall 2 issues with m; /archives//html/TenTec/2015-01/msg00019.html (12,386 bytes)
9. Re: [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Sun, 4 Jan 2015 16:08:50 +0000; Perhaps there's a good diagnostic to exercise the serial port that would reveal any slight data issues? Barry N1EU _______________________________________________ TenTec mailing list TenTec@contestin; /archives//html/TenTec/2015-01/msg00020.html (15,243 bytes)
10. Re: [TenTec] Orion II won't flash (score: 1): Author: N4BE_Jim--- via TenTec <tentec@contesting.com>; Date: Sun, 4 Jan 2015 21:00:18 -0500; Be sure no other program has seized the port, such as your logging program. Try shutting down all programs that use the serial port, then start the updater. Also check the port for baud rate etc. usi; /archives//html/TenTec/2015-01/msg00028.html (8,358 bytes)
11. Re: [TenTec] Orion II won't flash (score: 1): Author: Barry N1EU <barry.n1eu@gmail.com>; Date: Mon, 5 Jan 2015 09:22:47 +0000; Already checked all of these and none of them mattered - port consistently worked to flash my other Orions but wouldn't flash this one. Going to my old computer was the only thing that worked. Barry; /archives//html/TenTec/2015-01/msg00029.html (9,380 bytes)

Current List: 1 - 11
Page: [1]