Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Orion\s+meter\s+pegging\s+on\s+CW\s+TX\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Orion\s+meter\s+pegging\s+on\s+CW\s+TX\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Orion meter pegging on CW TX (score: 1): Author: "k3hx@juno.com" <k3hx@juno.com>; Date: Fri, 17 Feb 2006 21:50:19 GMT; When running at indicated PWR levels above "70" the meter needle pegs to the right when the transmitter is keyed on CW. I'd be grateful to know of a damping technique to remedy this. 73 Tim Colbert K; /archives//html/TenTec/2006-02/msg00802.html (6,878 bytes)
2. Re: [TenTec] Orion meter pegging on CW TX (score: 1): Author: "Chortek, Robert L" <robert.chortek@berliner.com>; Date: Sat, 18 Feb 2006 10:30:42 -0800; The needle on my Orion II goes to the peak value, whatever level that may be depending on the power level, and holds at that peak while I continue to xmit, without moving between dits and dahs. It is; /archives//html/TenTec/2006-02/msg00825.html (7,620 bytes)
3. Re: [TenTec] Orion meter pegging on CW TX (score: 1): Author: "k3hx@juno.com" <k3hx@juno.com>; Date: Sat, 18 Feb 2006 20:54:37 GMT; OM, My concern is with the initial dit or dah, the meter needle slams against the peg and then stays there as you noted. 73, Tim -- "Chortek, Robert L" <robert.chortek@berliner.com> wrote: The needle; /archives//html/TenTec/2006-02/msg00836.html (8,102 bytes)
4. Re: [TenTec] Orion meter pegging on CW TX (score: 1): Author: "Chortek, Robert L" <robert.chortek@berliner.com>; Date: Sat, 18 Feb 2006 13:05:11 -0800; Hi Tim. It sure does! You can even hear it slam on the right side of the meter enclosure. I have not heard of any broken needles though... Bob. OM, My concern is with the initial dit or dah, the mete; /archives//html/TenTec/2006-02/msg00839.html (9,164 bytes)
5. Re: [TenTec] Orion meter pegging on CW TX (score: 1): Author: "Ron Castro" <ronc@sonic.net>; Date: Sat, 18 Feb 2006 14:09:02 -0800; I think there are adjustment pots in the ADC/DAC, R337 and R340 of the A7 section (schematic 10) that effect the meter, although it may effect the S-Meter reading too. Best check with the factory, bu; /archives//html/TenTec/2006-02/msg00845.html (10,009 bytes)
6. Re: [TenTec] Orion meter pegging on CW TX (score: 1): Author: "Ron Castro" <ronc@sonic.net>; Date: Sat, 18 Feb 2006 14:10:29 -0800; I just looked closer and R337 is not adjustable, however R340 is. Ron N6AHA _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailm; /archives//html/TenTec/2006-02/msg00846.html (9,837 bytes)

Current List: 1 - 6
Page: [1]