Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+PTO\s+Backlash\s+help\s+needed\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+PTO\s+Backlash\s+help\s+needed\s*$/: 8 ]

Total 8 documents matching your query.

1. [TenTec] PTO Backlash help needed (score: 1): Author: Tom NØJMY <n0jmy@hayseedhamfest.com>; Date: Fri, 29 May 2009 20:05:34 -0500; Hello. New member here. I have some Century 21's here which seem to all exhibit dial backlash (maybe I should call it knob backlash) when turning the tuning knob counter-clockwise. The closer you get; /archives//html/TenTec/2009-05/msg00317.html (7,335 bytes)
2. Re: [TenTec] PTO Backlash help needed (score: 1): Author: wa3fiy@radioadv.com; Date: Sat, 30 May 2009 19:06:10 -0400; Hi Tom. Welcome. Good to see you here. I greatly enjoy your entertaining and informative posts to GlowBugs. :-) To your question. I'm no expert on the matter but I think the unidirectional backlash i; /archives//html/TenTec/2009-05/msg00328.html (9,995 bytes)
3. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Tom NØJMY <n0jmy@hayseedhamfest.com>; Date: Sat, 30 May 2009 20:34:19 -0500; Thank you very much, Lee. That gives me some things to think about. I've accumulated four of these rigs and have finally decided to spiff them up. So far I've removed three of the PTO's and have foun; /archives//html/TenTec/2009-05/msg00330.html (14,243 bytes)
4. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Tom NØJMY <n0jmy@hayseedhamfest.com>; Date: Sun, 31 May 2009 09:51:09 -0500; I'm very leery about celebrating too soon, so with much knocking on wood, I'm just going to report that the felt solution has favorably impressed me thus far. I doubled over a piece of felt, cut it o; /archives//html/TenTec/2009-05/msg00332.html (10,630 bytes)
5. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Jerry Kitterman <jerry.kitterman53@yahoo.com>; Date: Sun, 31 May 2009 08:35:43 -0700 (PDT); Hi Tom, Hope this finds you feeling much better than you were. I have been having some problems of my own but I'm not gonna bore you and go into them, you have enough of your own things; /archives//html/TenTec/2009-05/msg00333.html (12,600 bytes)
6. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Tom NØJMY <n0jmy@hayseedhamfest.com>; Date: Sun, 31 May 2009 15:06:39 -0500; Well, now that you've explained it, it seems pretty obvious. Thanks. Tom _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/; /archives//html/TenTec/2009-05/msg00334.html (11,326 bytes)
7. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Bwana Bob <wb2vuf@gti.net>; Date: Sat, 30 May 2009 08:33:21 -0400; Tom: Make sure that you have the correct grease. When I rebuilt my Corsair PTO, I used a light synthetic grease and had thr problem that you describe. I then switched to the "official" green Ten Tec; /archives//html/TenTec/2009-05/msg00335.html (9,986 bytes)
8. Re: [TenTec] PTO Backlash help needed (score: 1): Author: Bwana Bob <wb2vuf@gti.net>; Date: Sun, 31 May 2009 19:49:40 -0400; Tom: I found that on my Corsair and Century 22, the felt washer is very important for preventing the dial from springing back, especially at the edge of the band where spring tension is at maximum. O; /archives//html/TenTec/2009-05/msg00336.html (12,600 bytes)

Current List: 1 - 8
Page: [1]