Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Symptoms\s+of\s+logic\s+board\s+failure\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Symptoms\s+of\s+logic\s+board\s+failure\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Symptoms of logic board failure (score: 1): Author: "Zivney, Terry L." <00tlzivney@bsu.edu>; Date: Wed, 19 Jan 2011 17:56:37 -0500; I have seen lots of postings about "logic board failures" but haven't seen any listing of the symptoms (specific problems) that caused the owners to send their rigs in for repair. Is there any common; /archives//html/TenTec/2011-01/msg00455.html (6,954 bytes)
2. Re: [TenTec] Symptoms of logic board failure (score: 1): Author: NL7VL <neal.laugman@gmail.com>; Date: Thu, 20 Jan 2011 01:21:22 -0600; This issue is a * dead horse * to me so this is my last post on the topic. Hi Terry, I don't know if you are waiting for NT0F to answer your post, but I'll try to explain. While there have been probl; /archives//html/TenTec/2011-01/msg00462.html (9,714 bytes)
3. Re: [TenTec] Symptoms of logic board failure (score: 1): Author: Steve Halliburton <wa2soc@hsix.com>; Date: Thu, 20 Jan 2011 08:23:30 -0500; seen any listing of the symptoms (specific problems) that common problem? My VI/3 logic board seemed to have "failed" about two years ago. The radio was pretty much completely dead as far as control; /archives//html/TenTec/2011-01/msg00463.html (8,212 bytes)
4. Re: [TenTec] Symptoms of logic board failure (score: 1): Author: "Don Steele" <dsteele@iowatelecom.net>; Date: Fri, 21 Jan 2011 07:26:10 -0600; The original problem started during to 10 meter contest. All was working OK. I took a short break, and when I came back, the audio was dead on the rig. I cycled power, and at that point, the rig woul; /archives//html/TenTec/2011-01/msg00473.html (10,485 bytes)
5. Re: [TenTec] Symptoms of logic board failure (score: 1): Author: "Dr. Gerald N. Johnson" <geraldj@weather.net>; Date: Fri, 21 Jan 2011 19:22:13 -0600; The time base messes up the processors, both control and DSP. Likely the buttons are side effects of the control processor running poorly. And that could be an effect of the FSK also. Flickering mete; /archives//html/TenTec/2011-01/msg00479.html (12,422 bytes)
6. Re: [TenTec] Symptoms of logic board failure (score: 1): Author: "Don Steele" <dsteele@iowatelecom.net>; Date: Sun, 23 Jan 2011 13:20:40 -0600; Jerry, Here is what I have found so far. I opened up the rig, verified I was getting 13.6 volts to the logic board on connector 2. When I turned the rig on, the lower section of the display was out,; /archives//html/TenTec/2011-01/msg00505.html (15,464 bytes)

Current List: 1 - 6
Page: [1]