- 1. [TenTec] Titan Problem (score: 1)
- Author: k3sx@pipeline.com (Sidney D. Shusterman)
- Date: Mon, 03 Apr 2000 03:54:38 -0700
- One of the relays is sticking in my Titan Model 425. When this happens the relay(s)(?) stick in transmit. I have no receive signals. If I rap the case in the left lower rear corner the relay lets go
- /archives//html/TenTec/2000-04/msg00043.html (7,702 bytes)
- 2. [TenTec] Titan Problem (score: 1)
- Author: n4lq@iglou.com (Steve Ellington)
- Date: Mon, 3 Apr 2000 14:47:12 -0400 (EDT)
- Sounds like the relay is sticking. Someone suggested reversing the leads on the relay's coil as a fix. I'm not sure if it would help but maybe worth a shot. Steve Ellington N4LQ N4LQ@IGLOU.COM -- FAQ
- /archives//html/TenTec/2000-04/msg00045.html (8,151 bytes)
- 3. [TenTec] Titan Problem (score: 1)
- Author: chestert@pressroom.com (Chester Alderman)
- Date: Mon, 3 Apr 2000 19:36:56 -0400
- Hi Sid..I think EVERYONE who has a Titan has had that problem. In the 8 yrs I've had mine, I've probably replaced the relay at least six or seven times; but then I run it at 70+wpm full QSK also. The
- /archives//html/TenTec/2000-04/msg00050.html (8,690 bytes)
- 4. [TenTec] Titan Problem (score: 1)
- Author: aa4nn@juno.com (Joe L Blackwell)
- Date: Tue, 4 Apr 2000 16:37:18 -0500
- Had this happen to me during a contest, very frustrating. I would hit the dit side of my paddle to unstick it back into receive mode. Sometimes a coupla dits were needed. After a while, it cured itse
- /archives//html/TenTec/2000-04/msg00064.html (8,227 bytes)
- 5. [TenTec] Titan Problem (score: 1)
- Author: n1eu@hotmail.com (Barry N1EU)
- Date: Tue, 04 Apr 2000 13:39:50 EDT
- Been following this from the sidelines, but would appreciate it if someone would post Ten-Tec's price of the replacement relay. 73, Barry N1EU -- FAQ on WWW: http://www.contesting.com/tentecfaq.htm S
- /archives//html/TenTec/2000-04/msg00066.html (7,151 bytes)
- 6. [TenTec] Titan Problem (score: 1)
- Author: n4lq@iglou.com (Steve Ellington)
- Date: Tue, 4 Apr 2000 15:09:10 -0400 (EDT)
- The one for my Hercules II cost $175 if I recall correctly. Steve Ellington N4LQ N4LQ@IGLOU.COM -- FAQ on WWW: http://www.contesting.com/tentecfaq.htm Submissions: tentec@contesting.com Administrativ
- /archives//html/TenTec/2000-04/msg00070.html (7,427 bytes)
- 7. [TenTec] Titan Problem (score: 1)
- Author: Kannegaard@aol.com (Kannegaard)
- Date: Mon, 2 Mar 1998 00:41:24 EST
- I just acquired a Titan Amplifier with a little problem. The Grid Current always registers zero. The needle wiggles a little but doesn't indicate any significant grid current. With 10W in from my Par
- /archives//html/TenTec/1998-03/msg00005.html (7,036 bytes)
- 8. [TenTec] Titan Problem (score: 1)
- Author: k1ky@bellsouth.net (Tom Delker)
- Date: Mon, 02 Mar 1998 07:26:54 -0600
- There should be a dropping/sampling resistor in that circuit. Look there. -- Thomas M. Delker - K1KY CFO#395 - Smyrna / Gallatin / Short Mtn. TN C.A.T.S. (W4CAT) - 147.30 (114.8) / 145.23 / 223.98 /
- /archives//html/TenTec/1998-03/msg00006.html (7,257 bytes)
- 9. [TenTec] Titan Problem (score: 1)
- Author: k3mm@erols.com (Tyler Stewart)
- Date: Tue, 3 Mar 1998 00:20:21 -0000
- You might not see any significant grid current until you hit 50 or 60 watts input. It depends on the loading. Try hitting it with a little more juice and see what happens or decrease the loading. put
- /archives//html/TenTec/1998-03/msg00010.html (8,099 bytes)
- 10. [TenTec] Titan Problem (score: 1)
- Author: nw9g@netusa1.net (NW9G)
- Date: Mon, 02 Mar 1998 20:38:44 -0500
- To: <tentec@contesting.com> Jon, I am not too technical but I can say this about my Titan. I can usually run about 20 to 30 watts drive on 80 -20 meters and see plenty of grid current. (depending on
- /archives//html/TenTec/1998-03/msg00011.html (8,581 bytes)
- 11. [TenTec] Titan problem (score: 1)
- Author: k3mm@erols.com (Tyler G Stewart)
- Date: Thu, 27 Feb 1997 05:30:34 +0000
- Is there a TenTec representative on this reflector? I've got a Titan amplifier that had the 160 meter loading coil break loose during shipment from KP4 last year. I wasnt very impressed with the moun
- /archives//html/TenTec/1997-02/msg00151.html (6,870 bytes)
This search system is powered by
Namazu