- 1. [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Dave Edwards" <kd2e@comcast.net>
- Date: Sun, 23 May 2004 09:58:04 -0400
- I am going to fool around with the direct ins & outs to a sound card that my new argo comes with. Can anyone suggest a program to encode and decode cw, and how it hooks up? I can see how it uses the
- /archives//html/TenTec/2004-05/msg00714.html (6,984 bytes)
- 2. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Jim Miller WB5OXQ" <wb5oxq@grandecom.net>
- Date: Sun, 23 May 2004 11:34:48 -0500
- On my Omni 6+ there is a wire from a serial port with a little circuit with 2 resistors and 1 small transistor that goes straight to the straight key jack on the back fo the rig. MRP is one I have us
- /archives//html/TenTec/2004-05/msg00721.html (8,446 bytes)
- 3. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Tommy" <aldermant@alltel.net>
- Date: Sun, 23 May 2004 16:29:49 -0400
- I have been using YPlog for a little over three years. YPlog gives you the option of using the sound card generated CW audio, or the parallel port. I chose to use the sound card CW generation simply
- /archives//html/TenTec/2004-05/msg00732.html (8,729 bytes)
- 4. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: Robert & Linda McGraw K4TAX <RMcGraw@Blomand.Net>
- Date: Sun, 23 May 2004 15:40:15 -0500
- Can't specifically say about the Argonaut V but.......... in doing high speed CW for meteor scatter I use a piece of software to specifically generate and receive such. To that end the audio INs and
- /archives//html/TenTec/2004-05/msg00733.html (10,363 bytes)
- 5. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Dave Edwards" <kd2e@comcast.net>
- Date: Sun, 23 May 2004 18:11:41 -0400
- Bob....So are you just sending tones in sideband mode??? If you are on USB, and just using the line in, that is what it sounds like. ...Dave -- Original Message -- From: "Robert & Linda McGraw K4TAX"
- /archives//html/TenTec/2004-05/msg00737.html (11,459 bytes)
- 6. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: Robert & Linda McGraw K4TAX <RMcGraw@Blomand.Net>
- Date: Sun, 23 May 2004 20:10:40 -0500
- That is correct. A pure tone generates a pure carrier. Turn the tone on and off at the correct rate, sequence and duty cycle and one has code. The software along with the sound card generates CW for
- /archives//html/TenTec/2004-05/msg00744.html (13,661 bytes)
- 7. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: designer <designer@quickdata.com>
- Date: Sun, 23 May 2004 18:28:48 -0700
- CWType, from DxSoft, is free. It uses a small circuit - two diodes, two resistors, one transistor (all available at Radio Shack) - to key the rig. Your cable goes from the serial port to the key jack
- /archives//html/TenTec/2004-05/msg00746.html (8,280 bytes)
- 8. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Dave Edwards" <kd2e@comcast.net>
- Date: Sun, 23 May 2004 22:08:01 -0400
- Thanks Paul. I will look into it! ...Dave -- Original Message -- From: "designer" <designer@quickdata.com> To: <tentec@contesting.com> Sent: Sunday, May 23, 2004 9:28 PM Subject: Re: [TenTec] compute
- /archives//html/TenTec/2004-05/msg00748.html (9,074 bytes)
- 9. Re: [TenTec] computer CW my Argonaut V??? (score: 1)
- Author: "Carl Moreschi" <n4py@earthlink.net>
- Date: Mon, 24 May 2004 03:57:06 -0000
- My N4PY software for the Argonaut V will key the ArgoV without any keying interface. It just sends software commands to the radio to key it. The program also has a built in CW keyboard. See my webapg
- /archives//html/TenTec/2004-05/msg00755.html (9,416 bytes)
This search system is powered by
Namazu