- 1. [TowerTalk] 6M Transmission Line (score: 1)
- Author: Frank Davis <fdavis@nfld.net>
- Date: Thu, 18 Jul 2013 17:40:53 -0230
- Sent from an iPad2 _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.contesting.com/mailman
- /archives//html/Towertalk/2013-07/msg00391.html (7,223 bytes)
- 2. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: "Earl Morse" <kz8e@wt.net>
- Date: Fri, 19 Jul 2013 06:39:40 -0700
- LMR-600 is 50 ohms. Shouldn't be any problem. http://www.nr6ca.org/pdf/LMR600A.pdf If it were 75 ohms the simple answer would be that it would bump the VSWR of a matched 50 ohm system to 1.5:1. For t
- /archives//html/Towertalk/2013-07/msg00394.html (8,093 bytes)
- 3. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: Hector Garcia XE2K <j_hector_garcia@sbcglobal.net>
- Date: Fri, 19 Jul 2013 07:59:38 -0700 (PDT)
- There is no problem to run the LMR-600 , if you are sure you have the 75 ohms version you can "adjust" for 50 ohms for 6m, I did that for the 1/2 CATV who feed my 1/2 vertical for years before the
- /archives//html/Towertalk/2013-07/msg00396.html (9,746 bytes)
- 4. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: Jim Brown <jim@audiosystemsgroup.com>
- Date: Fri, 19 Jul 2013 08:39:19 -0700
- There is a simple, but tried and true method for using 75 ohm cable to feed a 50 ohm load. Simply make the 75 ohm line an EXACT multiple of half-wavelengths at the operating frequency. This works bec
- /archives//html/Towertalk/2013-07/msg00398.html (8,489 bytes)
- 5. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: Frank Davis <invl160@gmail.com>
- Date: Fri, 19 Jul 2013 17:02:44 +0000
- Thanks for replies re the LMR 600. Upon closer inspection i see no designation on the cable that refers to 75ohm...so I based on XE2K's note the cable is 50ohm. Will proceed to install the new cable
- /archives//html/Towertalk/2013-07/msg00399.html (7,327 bytes)
- 6. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: K8RI <K8RI-on-TowerTalk@tm.net>
- Date: Fri, 19 Jul 2013 14:05:44 -0400
- On 7/19/2013 10:59 AM, Hector Garcia XE2K wrote: There is no problem to run the LMR-600 , if you are sure you have the 75 ohms version you can "adjust" for 50 ohms for 6m, I did that for the 1/2 CATV
- /archives//html/Towertalk/2013-07/msg00400.html (10,793 bytes)
- 7. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: Steve Maki <lists@oakcom.org>
- Date: Fri, 19 Jul 2013 17:22:26 -0400
- They did change the model number, they decided on LMR600-75. Not sure why... We've used quite a bit of it - specs are very similar to .500 CATV hardline. -Steve K8LX There's a 75 ohm version of Times
- /archives//html/Towertalk/2013-07/msg00401.html (8,327 bytes)
- 8. Re: [TowerTalk] 6M Transmission Line (score: 1)
- Author: Hector Garcia XE2K <j_hector_garcia@sbcglobal.net>
- Date: Fri, 19 Jul 2013 14:28:02 -0700 (PDT)
- This is the link missing from my original email , the other was for the 1.125 clamps for the R25 tower http://www.tessco.com/products/displayProductInfo.do?sku=332355&eventPage=1 the specs are close
- /archives//html/Towertalk/2013-07/msg00402.html (12,763 bytes)
This search system is powered by
Namazu