Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Balun\s+for\s+older\s+Cushcraft\s+402CD\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Balun\s+for\s+older\s+Cushcraft\s+402CD\s*$/: 11 ]

Total 11 documents matching your query.

1. [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: Dave Thompson <thompson@mindspring.com>; Date: Thu, 18 Jan 2018 23:29:18 -0500 (GMT-05:00); I want to replace the 12 turn coax balun and coax on my older Cushcraft 2 el 40. Has anyone used the balun from the later XM-240? I don't see a rating on it and might look for a 4 or 5KW balun (1 to; /archives//html/Towertalk/2018-01/msg00151.html (7,871 bytes)
2. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: Timothy Coker via TowerTalk <towertalk@contesting.com>; Date: Fri, 19 Jan 2018 04:49:46 +0000 (UTC); I'd use a Balun Designs 1115t for that exact application. Use an appropriate sized Tywrap, some Scotch 88 and be done with it. I've had my pre-MFJ XM240 using the stock balun, but if doing it again I; /archives//html/Towertalk/2018-01/msg00152.html (8,186 bytes)
3. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: "john@kk9a.com" <john@kk9a.com>; Date: Fri, 19 Jan 2018 07:08:06 -0500; There are no special 402CD requirements, almost any 1:1 Balun will work and be better than the coil of coax. Many have screw terminals where you supply wire leads of the appropriate length to connect; /archives//html/Towertalk/2018-01/msg00154.html (8,389 bytes)
4. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: Richard Thorne <rthorne@rthorne.net>; Date: Fri, 19 Jan 2018 06:47:25 -0600; Dave, Go with a a balun designs ( balundesigns.com ) 1115d with the studs on top. Go from the balun studs to the element halves with a length of wire and ring terminals crimped/soldered. For mounti; /archives//html/Towertalk/2018-01/msg00155.html (9,094 bytes)
5. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: "Paul Christensen" <w9ac@arrl.net>; Date: Fri, 19 Jan 2018 08:07:15 -0500; Unless there's been a recent design change, Balun Designs (BD) doesn't seal in and around the stainless hardware. The gasketed cover seals are not the issue. I've experienced water leakage getting in; /archives//html/Towertalk/2018-01/msg00156.html (10,699 bytes)
6. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: <marsh@ka5m.net>; Date: Fri, 19 Jan 2018 07:20:42 -0600; I'd highly recommend the 1116dt from Balun Designs. (Optimized for 160M, 80M, and 40M.) http://www.balundesigns.com/model-1116d-1-31-mhz-5kw-optimized-for-low-frequ encies/ It is important to keep th; /archives//html/Towertalk/2018-01/msg00157.html (8,963 bytes)
7. [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: "Jim Thomson" <jim.thom@telus.net>; Date: Fri, 19 Jan 2018 10:06:58 -0800; <Dave, <Go with a a balun designs? ( balundesigns.com ) 1115d with the studs on <top.? Go from the balun studs to the element halves with a length of <wire and ring terminals crimped/soldered. <For m; /archives//html/Towertalk/2018-01/msg00158.html (9,468 bytes)
8. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: Richard Thorne <rthorne@rthorne.net>; Date: Fri, 19 Jan 2018 12:55:52 -0600; Jim Good points. It reminded me that my original post was for tribanders. The 1116 would be a better choice for 40m. Rich - N5ZC <Dave, <Go with a a balun designs? ( balundesigns.com ) 1115d with th; /archives//html/Towertalk/2018-01/msg00159.html (10,053 bytes)
9. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: Dave Thompson <thompson@mindspring.com>; Date: Fri, 19 Jan 2018 15:35:48 -0500 (GMT-05:00); Sounds like the 1116d is the best choice although I did find a K6NA 1 to 1 balun in my junk box. Rated at 5 KW. Thanks all 73 Dave K4JRB _______________________________________________ ______________; /archives//html/Towertalk/2018-01/msg00160.html (8,440 bytes)
10. Re: [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: "James Wolf" <jbwolf@comcast.net>; Date: Fri, 19 Jan 2018 15:50:56 -0500; I'd highly recommend the 1116dt from Balun Designs. (Optimized for 160M, 80M, and 40M.) http://www.balundesigns.com/model-1116d-1-31-mhz-5kw-optimized-for-low-frequ encies/ Does this balun put the dr; /archives//html/Towertalk/2018-01/msg00162.html (8,499 bytes)
11. [TowerTalk] Balun for older Cushcraft 402CD (score: 1): Author: "Jim Thomson" <jim.thom@telus.net>; Date: Sat, 20 Jan 2018 09:15:22 -0800; <I'd highly recommend the 1116dt from Balun Designs. (Optimized for 160M, 80M, and 40M.) http://www.balundesigns.com/model-1116d-1-31-mhz-5kw-optimized-for-low-frequ encies/ Does this balun put the d; /archives//html/Towertalk/2018-01/msg00167.html (8,961 bytes)

Current List: 1 - 11
Page: [1]