Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Dummy\s+Load\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Dummy\s+Load\s*$/: 7 ]

Total 7 documents matching your query.

1. Re: [TowerTalk] Dummy Load (score: 1): Author: "Fred Mott" <fredmott@zoominternet.net>; Date: Sun, 26 Apr 2009 15:26:26 -0700; It "The Tree" looks like the world's largest dummy load! Fred All: I have a 6M beam that is showing high SWR (10:1). I checked each connector to the antenna by disconnecting and placing a dummy load.; /archives//html/Towertalk/2009-04/msg00739.html (9,007 bytes)
2. Re: [TowerTalk] Dummy Load (score: 1): Author: "Michael Ryan" <mryan001@tampabay.rr.com>; Date: Sun, 26 Apr 2009 17:21:19 -0400; Scott, I might have missed this but what BRAND of antenna is this? If it is an M2, take a very hard look at the gamma match. The one on my 7ele is of 72ohm cable. The cable was cut and "F" connectors; /archives//html/Towertalk/2009-04/msg00744.html (10,932 bytes)
3. Re: [TowerTalk] Dummy Load (score: 1): Author: "Scott MacKenzie" <kb0fhp@comcast.net>; Date: Sun, 26 Apr 2009 20:25:09 -0400; It is an older Directive System's K1FO DS50-5 and I will look at that. I suspect it is moisture - or the center pin of the connetor - I am replacing both. Scott Scott, I might have missed this but wh; /archives//html/Towertalk/2009-04/msg00747.html (11,750 bytes)
4. [TowerTalk] Dummy Load (score: 1): Author: JOHN OWENS <ham38john@comcast.net>; Date: Tue, 27 Jul 2021 10:32:13 -0700 (PDT); If you have a Heahkit CanTenna dummy load, I would like to contact you re some observations/measurements I have made on mine. - John Owens - N7TK _______________________________________________ _____; /archives//html/Towertalk/2021-07/msg00150.html (6,607 bytes)
5. [TowerTalk] Dummy Load (score: 1): Author: JOHN OWENS <ham38john@comcast.net>; Date: Tue, 27 Jul 2021 13:56:11 -0700 (PDT); It is pretty clear that my Heathkit Dummy load is Dead. I need to measure my FTDX-101MP output on 6M (<200w) just to verify it is working as it should, before I start tearing into my 5el 6M beam inst; /archives//html/Towertalk/2021-07/msg00153.html (6,838 bytes)
6. Re: [TowerTalk] Dummy Load (score: 1): Author: "Lux, Jim" <jim@luxfamily.com>; Date: Tue, 27 Jul 2021 18:01:19 -0700; On 7/27/21 1:56 PM, JOHN OWENS wrote: It is pretty clear that my Heathkit Dummy load is Dead. I need to measure my FTDX-101MP output on 6M (<200w) just to verify it is working as it should, before I; /archives//html/Towertalk/2021-07/msg00154.html (7,939 bytes)
7. Re: [TowerTalk] Dummy Load (score: 1): Author: Wes <wes_n7ws@triconet.org>; Date: Wed, 28 Jul 2021 11:02:41 -0700; You can measure the load with an ohmmeter. If it's open or measures too high, check the four screws that center the bottom of the load resistor in the shield for tightness. Wes N7WS John Owens - N7; /archives//html/Towertalk/2021-07/msg00160.html (7,840 bytes)

Current List: 1 - 7
Page: [1]