Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+INstalling\s+guy\s+wires\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+INstalling\s+guy\s+wires\s*$/: 7 ]

Total 7 documents matching your query.

1. [TowerTalk] Installing guy wires (score: 1): Author: "Drax Felton" <draxfelton@gmail.com>; Date: Fri, 21 Nov 2008 22:41:01 -0500; I have got my 65-foot, Rohn 25g tower built up to the 30' level -- uninjured and not dead thanks to this forum. Many of you have been very helpful. Thank you. It's time to install the first set of gu; /archives//html/Towertalk/2008-11/msg00548.html (7,732 bytes)
2. Re: [TowerTalk] Installing guy wires (score: 1): Author: "Dick Green WC1M" <wc1m@msn.com>; Date: Sat, 22 Nov 2008 12:32:59 -0500; There are a number of ways to do what you want to do. Here are a few suggestions: 1. It's easier to assemble the guy anchor while the target section is on the ground. It's too late to do that with yo; /archives//html/Towertalk/2008-11/msg00555.html (15,167 bytes)
3. Re: [TowerTalk] Installing guy wires (score: 1): Author: Richards <jruing@ameritech.net>; Date: Sat, 22 Nov 2008 12:41:16 -0500; Pardon me... but don't these come with some sort of instruction manual you could consult? I thought you could get instructions even for older used towers... I would think the manual would tell you th; /archives//html/Towertalk/2008-11/msg00556.html (7,564 bytes)
4. [TowerTalk] INstalling guy wires (score: 1): Author: "Mitch" <mskobier@charter.net>; Date: Sun, 13 Dec 2015 13:46:29 -0800; All, I have stacked many a section of Rohn 25, and the method I have settled upon is as follows. I actually use a set of Kline cable grips to grasp the cable, but any of the previously mentioned meth; /archives//html/Towertalk/2015-12/msg00208.html (7,413 bytes)
5. Re: [TowerTalk] INstalling guy wires (score: 1): Author: Stan Stockton <wa5rtg@gmail.com>; Date: Mon, 14 Dec 2015 05:22:32 -0600; Another suggestion/alternative..A PLP preformed guy grip temporarily goes on and comes off the guy wire in less than 10 seconds and the loop is already made for you. You don't need to put but about 3; /archives//html/Towertalk/2015-12/msg00223.html (8,814 bytes)
6. Re: [TowerTalk] INstalling guy wires (score: 1): Author: David Aslin G3WGN <david@aslinvc.com>; Date: Mon, 14 Dec 2015 13:27:27 +0000; Hi all, I've been following this discussion with interest as I will be installing my first towers next spring. On this crowded island towers are relatively rare so there is not much local experience; /archives//html/Towertalk/2015-12/msg00227.html (10,269 bytes)
7. Re: [TowerTalk] INstalling guy wires (score: 1): Author: "Roger (K8RI) on TT" <K8RI-on-TowerTalk@tm.net>; Date: Mon, 14 Dec 2015 15:41:03 -0500; IF THEY ARE AVAILABLE: Big Grips, or by what ever name, they are really great to use. I use them with Phillystran but they are available for EHS as well. I use a ComeAlong to pretension to give the t; /archives//html/Towertalk/2015-12/msg00237.html (10,533 bytes)

Current List: 1 - 7
Page: [1]