- 1. [TowerTalk] LMR 900 Question (score: 1)
- Author: jreid@aloha.net (Jim Reid)
- Date: Sat, 14 Nov 1998 15:09:22 -1000
- Hi, I want to get more of my xmt signal out to the antenna field, and have been thinking about replacing my run of LMR 400 with LMR 900 -- it is a lot more expensive than what the 400 cost, but also
- /archives//html/Towertalk/1998-11/msg00462.html (8,170 bytes)
- 2. [TowerTalk] LMR 900 Question (score: 1)
- Author: Dick Green" <dick.green@valley.net (Dick Green)
- Date: Sun, 15 Nov 1998 00:00:37 -0500
- Jim, Please summarize the replies you get on this. I'm interested in doing exactly the same thing -- replacing 260 feet of LMR400 with LMR900. Another reason I may need to use the LMR600 instead of (
- /archives//html/Towertalk/1998-11/msg00470.html (9,943 bytes)
- 3. [TowerTalk] LMR 900 Question (score: 1)
- Author: n7ex@athenet.net (Dave_K9NX)
- Date: Sun, 15 Nov 1998 13:09:06 +0000
- <snip> Seems like a lot of money to pay for a .4db and .8db increase in signal on 20 and 15. <SNIP> All hard line is coax not all coax is hardline. The LM series is just coax since it uses a braid fo
- /archives//html/Towertalk/1998-11/msg00474.html (8,948 bytes)
- 4. [TowerTalk] LMR 900 Question (score: 1)
- Author: basalop@gte.net (Jim Berry)
- Date: Sun, 15 Nov 1998 20:59:10 -0800
- Hello TowerTalk Dudes, I'm confused. What is LMR 400 and 900? Is that 75 ohm stuff used by the cable TV industry? I have used the 1/2 and 3/4 inch hardline stuff with good success. If you are going t
- /archives//html/Towertalk/1998-11/msg00488.html (8,906 bytes)
- 5. [TowerTalk] LMR 900 Question (score: 1)
- Author: 107770.3462@compuserve.com (James P. Cassidy)
- Date: Mon, 16 Nov 1998 01:18:13 -0500
- Jim, You can get the F- fittings for the RG6U and the smaller RG59U at Radio Shack, they have a couple of different grades. Also they have inexpensive strippers and crimpers for them. I have also see
- /archives//html/Towertalk/1998-11/msg00490.html (7,856 bytes)
- 6. [TowerTalk] LMR 900 Question (score: 1)
- Author: n7ex@athenet.net (Dave_K9NX)
- Date: Mon, 16 Nov 1998 12:20:36 +0000
- The LMR series of coax is a low loss version of 50 Ohm coax. It comes in a variety of sizes. The larger sizes as you might expect all take special connectors as it is all non standard diameters. It i
- /archives//html/Towertalk/1998-11/msg00494.html (8,263 bytes)
- 7. [TowerTalk] LMR 900 Question (score: 1)
- Author: DavisRFinc@aol.com (DavisRFinc@aol.com)
- Date: Mon, 16 Nov 1998 11:40:35 EST
- Hi ALL, Dave hits the key points right on. To add, you can direct bury any standard version of LMR. If you are concerned that a pick ax, back hoe, etc. might cut the jacket, get the "DB" version, dir
- /archives//html/Towertalk/1998-11/msg00504.html (9,689 bytes)
This search system is powered by
Namazu