- 1. [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Byron Tatum <bjtatum1@att.net>
- Date: Thu, 24 Mar 2022 03:14:44 +0000 (UTC)
- Anyone know where to obtain rotor and bearing shelves for the 65G tower?Thanks, Byron W5FH _______________________________________________ _______________________________________________ TowerTalk ma
- /archives//html/Towertalk/2022-03/msg00080.html (6,444 bytes)
- 2. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Grant Saviers <grants2@pacbell.net>
- Date: Thu, 24 Mar 2022 07:28:46 -0700
- I couldn't find them commercially, so had my design waterjet cut from 1/4" A36 plate and hot dip galvanized. Plasma or laser cutting would also work fine and likely be cheaper. Grant KZ1W ___________
- /archives//html/Towertalk/2022-03/msg00082.html (7,489 bytes)
- 3. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Gary Johnson via TowerTalk <towertalk@contesting.com>
- Date: Thu, 24 Mar 2022 09:47:52 -0700
- Grant saved the day for me on a 65G project. His DXF file for the rotator shelf worked fine at the waterjet shop. I used 3 in. angle and U bolts to fix it to the legs. For a top plate to hold a beari
- /archives//html/Towertalk/2022-03/msg00083.html (7,874 bytes)
- 4. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Steve Maki <lists@oakcom.org>
- Date: Thu, 24 Mar 2022 13:45:11 -0400
- **resent in straight ascii mode. When I needed the same for my R80 tower I decided to side mount my big 3L 40. I only needed a bunch of angle, a piece of pipe for the collar, and the mast of course.
- /archives//html/Towertalk/2022-03/msg00084.html (8,802 bytes)
- 5. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Ken Alker <ka6ken@alker.net>
- Date: Thu, 24 Mar 2022 10:55:13 -0700
- As a newbie, what is the advantage to side-mounting, as you've shown in your picture? **resent in straight ascii mode. When I needed the same for my R80 tower I decided to side mount my big 3L 40. I
- /archives//html/Towertalk/2022-03/msg00085.html (9,173 bytes)
- 6. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Steve Maki <lists@oakcom.org>
- Date: Thu, 24 Mar 2022 15:00:35 -0400
- Easier to install, since you don't have to drop your mast in thru the tower top. Easier to service, especially the rotator. You simply clamp the mast (using a muffler clamp just above the top of the
- /archives//html/Towertalk/2022-03/msg00086.html (10,528 bytes)
- 7. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: <john@kk9a.com>
- Date: Fri, 25 Mar 2022 15:05:50 -0400
- Perhaps K7PN or K0XG can make those components for you. I worked in manufacturing so I was able to make the plates for my Rohn 65 tower myself. If you can draw them with a CAD system it should not be
- /archives//html/Towertalk/2022-03/msg00092.html (7,650 bytes)
- 8. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Bill Putney <billp@wwpc.com>
- Date: Fri, 25 Mar 2022 15:20:46 -0700
- Id try Send Cut Send. They are fast and reasonably priced. Bill Putney Chief Engineer - KPTZ El Jefe de Contenido - Port Townsend Film Festival Private Pilot-Single Engine Land | Airframe & Powerplan
- /archives//html/Towertalk/2022-03/msg00093.html (9,192 bytes)
- 9. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: "Jon Zaimes, AA1K via TowerTalk" <towertalk@contesting.com>
- Date: Fri, 25 Mar 2022 22:56:21 +0000 (UTC)
- On the Rohn 65 at W3PP (SK) two flat plates were used for rotor and bearing. The mast held a 5-element 46-foot boom 20-meter yagi. at 130 feet. The flat plates were about 1/2" thick aluminum as I re
- /archives//html/Towertalk/2022-03/msg00094.html (9,784 bytes)
- 10. Re: [TowerTalk] Rohn 65G Accessories (score: 1)
- Author: Grant Saviers <grants2@pacbell.net>
- Date: Sat, 26 Mar 2022 10:32:50 -0700
- DIY plasma cutters that easily cut 1/4" are ridiculously cheap, and easy to use. I make a pattern in plywood with offset enough to compensate for the kerf to torch edge. Clamp the top plate to a towe
- /archives//html/Towertalk/2022-03/msg00095.html (9,101 bytes)
This search system is powered by
Namazu