Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Thrust\s+bearing\s+shot\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Thrust\s+bearing\s+shot\s*$/: 6 ]

Total 6 documents matching your query.

1. [TowerTalk] Thrust bearing shot (score: 1): Author: "K8RI on Tower talk" <k8ri-tower@charter.net>; Date: Fri, 12 May 2006 18:33:41 -0400; I thought I'd pass on some information. It seems like even with care planning for problems when pushing the limits the problems turn up where we don't expect them. I'm running a 97 foot ROHN 45G. The; /archives//html/Towertalk/2006-05/msg00232.html (8,323 bytes)
2. Re: [TowerTalk] Thrust bearing shot (score: 1): Author: Dino Darling <dino@k6rix.com>; Date: Fri, 12 May 2006 16:25:06 -0700; Hey Roger! I can't wait for the new set of pictures to be uploaded to your antenna web site! Your old bearings are designed for radial loads only (I know, Dino is preaching to the choir again). I kno; /archives//html/Towertalk/2006-05/msg00235.html (10,901 bytes)
3. Re: [TowerTalk] Thrust bearing shot (score: 1): Author: ersmar@comcast.net; Date: Sat, 13 May 2006 03:46:23 +0000; Roger: I used a self-centering industrial bearing at the top of my tower, similar to: http://www.applied.com/catalog/ma/catalog.do?e=10&s=2000776&r=0 . I lube it once each year with marine grease. It; /archives//html/Towertalk/2006-05/msg00238.html (10,902 bytes)
4. Re: [TowerTalk] Thrust bearing shot (score: 1): Author: "K8RI on Tower talk" <k8ri-tower@charter.net>; Date: Sat, 13 May 2006 00:22:08 -0400; I've thought of those as well as taper bearings (like a wheel bearing of the proper size but with both races) In that case you do have to cut inner and outer retaining rings though. My big problem w; /archives//html/Towertalk/2006-05/msg00240.html (12,869 bytes)
5. Re: [TowerTalk] Thrust bearing shot (score: 1): Author: jperalta@tampabay.rr.com; Date: Sat, 13 May 2006 10:21:17 -0400; This is very simular to the one UST uses. With the exception that the mast diameter is 2 1/16" and has a 2 hole bolt pattern. I wonder if the 2" hole would be too small for some masts? Julio, W4HY to; /archives//html/Towertalk/2006-05/msg00246.html (12,811 bytes)
6. Re: [TowerTalk] Thrust bearing shot (score: 1): Author: <ersmar@comcast.net>; Date: Sat, 13 May 2006 10:54:03 -0400; Julio: The ID of my mast bearing is in fact the next size up from 2 inches. I had originally purchased a 2 inch bearing but that was too small, so I returned it and asked for the next larger size. I; /archives//html/Towertalk/2006-05/msg00247.html (13,724 bytes)

Current List: 1 - 6
Page: [1]