Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+US\s+Tower\s+MA40\s+mast\s+oops\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+US\s+Tower\s+MA40\s+mast\s+oops\s*$/: 6 ]

Total 6 documents matching your query.

1. [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Kurt Cathcart, KR2C" <Kurt@KuhlRoad.net>; Date: Sun, 31 Oct 2010 17:40:15 -0400; I've been working on putting up a US Tower MA$ rotatable mast. In my haste to put the mast vertical for the first time, the 2" innermost section wasn't tightened down and slid in to the base section.; /archives//html/Towertalk/2010-10/msg00427.html (9,002 bytes)
2. Re: [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Richard M. Gillingham" <rmoodyg@bellsouth.net>; Date: Sun, 31 Oct 2010 17:49:36 -0400; I'd lower the mast to horizontal and remove the bottom cap. You should be able to remove the top mast section from there. You'll need a wrench to remove the screws securing the cap and a block of woo; /archives//html/Towertalk/2010-10/msg00428.html (9,980 bytes)
3. Re: [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Kurt Cathcart, KR2C" <Kurt@KuhlRoad.Net>; Date: Tue, 02 Nov 2010 08:47:37 -0400; Gil, Thank you for the reply. I took a look at the end cap yesterday. This looks like one of those things that would be a PITA to get lined back up. Have you done this? If so, how difficult was it re; /archives//html/Towertalk/2010-11/msg00007.html (9,045 bytes)
4. Re: [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Kurt Cathcart, KR2C" <Kurt@KuhlRoad.net>; Date: Wed, 03 Nov 2010 18:21:09 -0400; OK. I pulled the bottom cap off and inside was the 3" square inner mast. Attached to this was the bracket for the raising cable and also a 4" round plate to guide it through the outer mast. i unhooke; /archives//html/Towertalk/2010-11/msg00041.html (8,620 bytes)
5. Re: [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Dino Darling" <dino@kx6d.com>; Date: Thu, 04 Nov 2010 06:36:13 -0700; You need invert the 3" tube slightly, so the top of the 3" tube is angled down. Use a smaller pipe that will fit INSIDE of the 2" mast so you can lift and align it with the 6" 2.5" stub thats welded; /archives//html/Towertalk/2010-11/msg00053.html (9,544 bytes)
6. Re: [TowerTalk] US Tower MA40 mast oops (score: 1): Author: "Kurt Cathcart, KR2C" <Kurt@KuhlRoad.net>; Date: Sat, 06 Nov 2010 16:01:32 -0400; Dino, This worked great. Thanks for the help. -Kurt KR2C _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.co; /archives//html/Towertalk/2010-11/msg00061.html (10,327 bytes)

Current List: 1 - 6
Page: [1]