- 1. [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: Tom Horton <k5iid@sbcglobal.net>
- Date: Wed, 21 May 2014 21:07:57 -0700 (PDT)
- There is no joy in Mudville! http://www.dfwcontest.com K5IID Tom Horton Hillsboro, TX E sorter for ARRL W5 bureau Same call for 57 years! _______________________________________________ ____________
- /archives//html/Towertalk/2014-05/msg00413.html (7,452 bytes)
- 2. [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: Tom Horton <k5iid@sbcglobal.net>
- Date: Wed, 21 May 2014 21:12:17 -0700 (PDT)
- OOPS!!!< I did it again! Sorry! Does any one have the pin out for rotor itself? Thanks, Tom K5IID There is no joy in Mudville! http://www.dfwcontest.com K5IID Tom Horton Hillsboro, TX E sorter for AR
- /archives//html/Towertalk/2014-05/msg00414.html (7,832 bytes)
- 3. Re: [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: Pete Smith N4ZR <n4zr@contesting.com>
- Date: Thu, 22 May 2014 05:47:19 -0400
- My manual shows a 7-pin connector with 6 wires used. Each pin goes to the corresponding number on the controller input. Pins 4 and 5 are the motor. Pin 3 is ground and one end of the pot. Pin 2 is th
- /archives//html/Towertalk/2014-05/msg00415.html (8,953 bytes)
- 4. Re: [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: Bill Turner <dezrat@outlook.com>
- Date: Thu, 22 May 2014 08:05:52 -0700
- ORIGINAL MESSAGE: (may be snipped) On 5/22/2014 2:47 AM, Pete Smith N4ZR wrote: My manual shows a 7-pin connector with 6 wires used. Each pin goes to the corresponding number on the controller input.
- /archives//html/Towertalk/2014-05/msg00417.html (8,473 bytes)
- 5. Re: [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: "K0DAN" <k0dan@comcast.net>
- Date: Thu, 22 May 2014 11:21:56 -0500
- The SDX and DXA use different connectors but the pin outs are the same and the rotors and controllers are interchangeable if you make up a pigtail to change connector types and genders. The manual is
- /archives//html/Towertalk/2014-05/msg00418.html (9,428 bytes)
- 6. Re: [TowerTalk] Yaesu G-800sdx rotor pinout (score: 1)
- Author: Pete Smith N4ZR <n4zr@contesting.com>
- Date: Thu, 22 May 2014 14:45:28 -0400
- Sorry, I should have been clearer. I have a G-800SA and a G-1000DXA. The controller end connectors are interchangeable, and either controller works with either rotator. Should you want to verify what
- /archives//html/Towertalk/2014-05/msg00422.html (10,088 bytes)
This search system is powered by
Namazu