- 1. [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: Jerry <grf@npgcable.com>
- Date: Thu, 08 Dec 2011 13:50:39 -0700
- My 1000 DXA's dial lamp burned out...again. I have searched everywhere in an attempt to find someone's article on replacing this lamp with LED's but no luck so far. Does anyone have or can steer me t
- /archives//html/Towertalk/2011-12/msg00225.html (6,532 bytes)
- 2. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: Jim Brown <jim@audiosystemsgroup.com>
- Date: Thu, 08 Dec 2011 14:55:39 -0800
- This came up several months ago. Search the archives. It's a tough lamp to replace. Rather than attempt it, I found some nice bright LEDs and managed to squeeze them into the right side of the bezel
- /archives//html/Towertalk/2011-12/msg00226.html (7,431 bytes)
- 3. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Larry" <lknain@nc.rr.com>
- Date: Thu, 8 Dec 2011 18:41:24 -0500
- IdiomPress makes a small illuminator board for HyGain rotor boxes which might work. It has 3 LEDs and is intended to sit on top of a meter with a clear top. It has a rectifier to get the DC voltage f
- /archives//html/Towertalk/2011-12/msg00231.html (9,392 bytes)
- 4. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: EZ Rhino <EZRhino@fastmovers.biz>
- Date: Thu, 8 Dec 2011 16:46:10 -0700
- I have one of these kits. The kit is fine, works fine, marginally bright enough in my opinion...probably not quite as bright as the stock bulb. Getting the kit is the problem...order it and wait 6 mo
- /archives//html/Towertalk/2011-12/msg00232.html (7,871 bytes)
- 5. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Larry" <lknain@nc.rr.com>
- Date: Thu, 8 Dec 2011 19:54:45 -0500
- I got mine in a couple of days. It has a jumper scheme to set the intensity in addition to a height setting when soldering the LEDs. I haven't installed mine yet so I don't know how the actual intens
- /archives//html/Towertalk/2011-12/msg00247.html (8,760 bytes)
- 6. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Anthony W. DePrato" <wa4jqs@mikrotec.com>
- Date: Thu, 08 Dec 2011 20:11:21 -0500
- hate you had the problems Chris . i have ordered 3 rotor ez kits then two of the led kits and later a SCAR filter. got them all within a week to ten days. superbrightleds has both leds with leads or
- /archives//html/Towertalk/2011-12/msg00248.html (9,864 bytes)
- 7. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Mike" <noddy1211@sbcglobal.net>
- Date: Thu, 8 Dec 2011 17:48:32 -0800
- I did this a while ago using a super bright LED with my G-1000 controller. I used one LED with a 450 OHM limiting resistor (the LED package will tell you what value resistor to use). Because the ligh
- /archives//html/Towertalk/2011-12/msg00249.html (11,426 bytes)
- 8. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Stan Labinsky Jr." <wa2puq@frontiernet.net>
- Date: Fri, 9 Dec 2011 21:05:09 -0500
- Three small leds in series, would drop about 6 volts. At 20 mA, from a 12 volt DC supply a typical value for the dropping resistor would be about 330 ohms. A small full wave bridge rectifier would be
- /archives//html/Towertalk/2011-12/msg00262.html (10,258 bytes)
- 9. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Anthony W. DePrato" <wa4jqs@mikrotec.com>
- Date: Sat, 10 Dec 2011 08:29:44 -0500
- I. P. Makes the kit for some Yasua rotors.. your may very well be one of them' check the website 73 Tony Anthony W. DePrato WA4JQS Since Sept 9th 1962 CQ DX HALL OF FAME # 39 DXCC HONOR ROLL FOUNDER
- /archives//html/Towertalk/2011-12/msg00263.html (8,859 bytes)
- 10. Re: [TowerTalk] Yaesu Rotor Dial Lamp (score: 1)
- Author: "Jim Hargrave" <w5ifp@gvtc.com>
- Date: Sat, 10 Dec 2011 08:42:22 -0600
- You don't really need the full wave bridge. Install a 1N4000 (or equivalent) in series with the LED/resistor and a 10 mfd capacitor across the LED's. The 1N4000 protects the LED's from reverse voltag
- /archives//html/Towertalk/2011-12/msg00264.html (11,608 bytes)
This search system is powered by
Namazu