Amps
[Top] [All Lists]

Re: [Amps] 220V service for amplifier

To: Bill Coleman <n2bc@stny.rr.com>
Subject: Re: [Amps] 220V service for amplifier
From: jsb@digistar.com
Reply-to: jsb@digistar.com
Date: Wed, 3 Dec 2003 09:17:51 -0500 (EST)
List-post: <mailto:amps@contesting.com>
On Wed, 3 Dec 2003, Bill Coleman wrote:

> NEVER 'consider' or tie neutral to ground. They are NOT the same....
> Neutral carries current by design, the ground should never carry current
> unless there is a fault.



If the Centurion has a 4 wire power cord:
  I will tie the chassis ground to the ground in the feed, the amp's bond
to the feed's neutral and the 110V single phase lines to the amp's
black/red.

The idea being to use the neutral as a means to return fault current and
the ground to chassis ground.



If the Centurion only has 3 wires in its power cord:
  I will tie the 110V lines to the amp's black/red and tie the amp's
ground to neutral and run a chassis ground to the ground and also to my
shack ground (copper braid to a ground rod outside).


Is there an issue with tying my breaker panel ground to my shack's ground?


thanks,
Jason



> ----- Original Message -----
> From: "Joe Isabella" <n3ji@yahoo.com>
> To: "Amps" <amps@contesting.com>
> Sent: Tuesday, December 02, 2003 12:02 PM
> Subject: Re: [Amps] 220V service for amplifier
>
>
> > Jason,
> > The "old" standard was only three wires for dryers (two Hots and a
> Neutral), but I'm pretty sure
> > that new homes have 4 wire dryer outlets now.  Consider the Neutral to be
> ground, since they are
> > tied together in your breaker box anyway.  I simply used the three-wire
> dryer outlet (30A) since
> > my amp came with the three-wire plug.  Also, you might consider the 15 or
> 20A style of 240V
> > outlets if you're doing yours from scratch.  I've seen several HF Amps
> done that way.  It's the
> > ones that look just like 120V outlets but have one or both of the prongs
> turned sideways (like on
> > large window ACs).  I'm suggesting this because I had a bit of trouble
> finding the dryer
> > plugs/outlets at Home Depot...
> >
> > Joe,
> > N3JI
> >
> > --- Jason Buchanan <jsb@digistar.com> wrote:
> > >
> > > I did some searching through the list but haven't managed to hit the
> > > nail right on the head yet...
> > >
> > > For wiring a Ten-Tec Centurion amp to 220V, are there any recommended
> > > plugs and outlets to use?
> > >
> > > I am thinking about using a 3 or 4 prong clothes dryer outlet and plug
> > > combination for quick/easy disconnect, however the thing i'm wondering
> > > about is where the neutral and ground tie together, since i'm fairly
> > > sure that the Centurion doesn't have a 4 wire power cable running out of
> > > it.  Maybe i'm wrong (probably am wrong).
> > >
> > >
> > > Any help and advice how to properly wire the amp would be greatly
> > > appreciated.
> > >
> > >
> > >
> > > thanks,
> > > Jason
> > >
> > > _______________________________________________
> > > Amps mailing list
> > > Amps@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/amps
> >
> >
> > __________________________________
> > Do you Yahoo!?
> > Free Pop-Up Blocker - Get it now
> > http://companion.yahoo.com/
> > _______________________________________________
> > Amps mailing list
> > Amps@contesting.com
> > http://lists.contesting.com/mailman/listinfo/amps
> >
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>