Steve, that seems to be the final word, then. When I
Google'd "10218A" I got some hits, but not many. When
I Google "11536A", I find lots of companies selling
them used. As you say, the difference is that the
11536A is a TEE fitting, and the 10218A is purely a
probe tip-to-BNC adapter, which I then use with a BNC
tee.
One final note - the accessory kit 11570A contained
two of the 11536A tees, and some 50 ohm loads and
splitters. The 908A load is particularly useful as it
is a precision 50 ohm reference for calibration.
Often, the 11570A is easier to find than any of the
constituent parts.
73,
Dave
--- Steve Katz <stevek@jmr.com> wrote:
> I tried to reply to this, but somehow it didn't post
> (I don't think).
>
> The 8405A standard 50 Ohm tee accessory that fits
> the VVM probe tips
> perfectly is P/N 11536A.
>
> I have several, and see them surplus all the time.
> They're passive, so it
> would be rare to find a "bad" one.
>
> -WB2WIK/6
>
> -----Original Message-----
> From: Dave Haupt [mailto:emailw8nf@yahoo.com]
> Sent: Thursday, March 10, 2005 9:45 AM
> To: amps@contesting.com; dansawyer@earthlink.net
> Subject: [BULK] - Re: [Amps] hp 8405a operations ??
>
>
> A probe tip to BNC male adapater was HP part number
> 10218A. A trio of them sold on ebay a few weeks ago
> for $77. They show up on rare occasion there.
> Alternate part number for the same part is
> 10218-60001.
>
> A few years ago, I sucked in my gut and paid $90
> each
> for two of them, brand new, from Agilent.
>
> In theory, this adapter is part of the oscilloscope
> accessories product line. If they offer a catalog
> of
> scope probes and accessories, you might find a
> reference in there.
>
> I wouldn't want to have to attempt to repair a
> broken
> probe tip. I keep my 8405A's probes wrapped in pink
> bubble wrap when I'm not using the instrument.
>
>
> 73,
>
> Dave W8NF
>
> ===In reply to====
>
> Date: Thu, 10 Mar 2005 06:43:16 -0800
> From: Dan Sawyer <dansawyer@earthlink.net>
> Subject: [Amps] hp 8405a operations ??
> To: amps <amps@contesting.com>
>
> All,
>
> Based on input here and other places I purchased an
> 8405A. I have also
> found a pdf for the service manual on line so have
> some idea about how
> to use it. That said I have a very low level
> question
> regarding
> connecting the probes. I constructed a very simple
> phase system by
> connecting a 500 MHz 0db source to two 6 foot 50 ohm
> cables connected
> together and terminated in 50 ohms. I connected one
> probe to the signal
> at the terminator and one probe at the junction of
> the
> 2 cables. This
> effectively should measure the phase of a 500 MHz
> signal over 6 feet.
>
> The long and the short of it is this seemed to work.
> The unit locked in
> and measured the phase. That said the actual
> connecting the probes was
> very awkward. This unit has only the bear point at
> the
> probe tips.
> making a connection is problematic. Does HP have
> "probe ends" that can
> "lock" on? Does anyone know if these tips are
> "standard" in the HP
> line?
>
> Sorry for such a simple question but getting the
> instrument to read
> consistently is the first step in using it.
>
> Dan
>
>
>
> __________________________________
> Do you Yahoo!?
> Yahoo! Small Business - Try our new resources site!
> http://smallbusiness.yahoo.com/resources/
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
__________________________________
Do you Yahoo!?
Yahoo! Mail - Find what you need with new enhanced search.
http://info.mail.yahoo.com/mail_250
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|