Amps
[Top] [All Lists]

Re: [Amps] questions about hi pot tester

To: Amps Reflector <amps@contesting.com>
Subject: Re: [Amps] questions about hi pot tester
From: Dan Evans <dan.evans@insightbb.com>
Date: Sun, 06 Jan 2008 09:45:06 -0500
List-post: <mailto:amps@contesting.com>
Tried to post this once, but my message was bounced...


If anyone is looking at building hi-pots, I have quite a few of these 
microwave oven parts on hand.

The transformers would be a bit expensive to ship, but I also have lots 
of diodes and caps.

I'm open to reasonable offers, or even trades:-)

73
Dan
-- 
K9ZF /R no budget Rover ***QRP-l #1269 
Check out the Rover Resource Page at: <http://www.qsl.net/n9rla> 
List Administrator for: InHam+grid-loc+ham-books 
Ask me how to join the Indiana Ham Mailing list! 



TexasRF@aol.com wrote:
>  
> One useful source of high voltage parts is from old microwave ovens. In  
> particular, the power transformer, filter capacitors and diodes are plentiful 
>  and 
> cheap on Ebay.
>  
> The filter caps are typically .95 microfarads and will easily handle more  
> than 6500vdc. One transformer, four diodes in a 4X multplier and four 
> capacitors 
>  will generate approximately 13kv.
>  
> To prevent damage to the component under test, the current should be  
> limited. One very easy way to do that is by using a Tripplett 630, set for 
> 6kv,  in 
> series with the output. The 630 will indicate full scale at a current flow of 
>  
> 60 microamps and what ever the reading is in volts should be deducted from 
> the 
>  power supply voltage reading to determine the actual breakdown voltage.
>  
> I use a small 2 amp Variac to vary the primary voltage, allowing output  
> voltage to be set over a range of 0 to 13kv. At greater than 6kv, I use two 
> 630  
> meters in series and add their readings to measure the output voltage.
>  
> Yes it is a kludge, but it does work quite well, especially considering the  
> cost.
>  
> 73,
> Gerald K5GW
>  
>  
> In a message dated 1/3/2008 2:37:58 P.M. Central Standard Time,  
> barrie@centric.net writes:
>
> Commander!
>
> I was in much the same position, in that I had  gathered almost all that I
> needed to build a hipot, but the filter caps  kept getting away, especially
> price-wise.
>
> I ended up buying a  commercial unit on EBay, in the "Industrial  Electronics"
> section.
>
> Continusously variable voltage from zero to 15  KV, variable load from 2
> microamps on up, two big meters and looks as if it  had never been used.
>
> $100.00, shipping included.
>
> 73, Barrie,  W7ALW
> ----- Original Message ----- 
> From: "Commander John"  <crazytvjohn@yahoo.com>
> To: "Steve Katz"  <stevek@jmr.com>
> Cc: <Amps@contesting.com>
> Sent: Thursday,  January 03, 2008 1:18 PM
> Subject: Re: [Amps] questions about hi pot  tester
>
>
>   
>> The application is to ham radio related stuff. Not  commercial.  I do not
>>     
> know what I may need to test in the future, so I  do not know what to get in
> a tester.
>   
>>   john  w9zy
>>
>> Steve Katz <stevek@jmr.com>  wrote:
>>   What's the application?
>>
>> A lot of  off-the-shelf hipot testers for consumer electronic equipment
>> stop at  6kVdc (because that's the limit of the requirement for
>> compliance  testing on a 240V circuit) and that's not nearly high enough
>> voltage  to test, say, a high power transmitting tube.
>>
>> Are you looking  to do compliance testing, which requires a stipulated
>> ramp time, dwell  time and leakage limit? Or just to see where stuff
>> flashes over? How  high a voltage?
>>
>> WB2WIK/6
>>
>>  _______________________________________________
>> Amps mailing  list
>> Amps@contesting.com
>>  http://lists.contesting.com/mailman/listinfo/amps
>>
>>     
>
>
> _______________________________________________
> Amps  mailing  list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
>
>
>
>
>
> **************Start the year off right.  Easy ways to stay in shape.     
> http://body.aol.com/fitness/winter-exercise?NCID=aolcmp00300000002489
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>   
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>