Carl,
I'm not seller.But I think it should without minimum order, even 1 piece
should be OK, If any guy interested in it, I would like help you.FREE!
Hsu
-----原始邮件-----
From: Carl
Sent: Saturday, October 11, 2014 8:31 AM
To: Chris Fox ; steve@nr4m.com
Cc: Amps
Subject: Re: [Amps] Source for replacement PS caps
What is the minimum order to get your own name on caps from China?
Carl
KM1H
----- Original Message -----
From: "Chris Fox" <ni4ldipole@gmail.com>
To: <steve@nr4m.com>
Cc: "Amps" <amps@contesting.com>
Sent: Friday, October 10, 2014 7:08 PM
Subject: Re: [Amps] Source for replacement PS caps
Hi Steve,
I have plenty of screw type caps.....
http://www.ni4l.com/capacitor-500v-270uf-capacitor-lot-of-8
ᐧ
Thank you
73
Chris Fox Ni4L
828-855-8869
Ni4L Antennas & Electronics
2646 Old Wilkesboro rd
Taylorsville, NC
28681
http://ni4l.com
https://www.facebook.com/Ni4LAntennas
*Hours: Monday-Friday 9:00 am-5:00 pm Eastern*
*"Chance favors the prepared mind" *
On Fri, Oct 10, 2014 at 3:16 PM, Steve NR4M <steve@nr4m.com> wrote:
Thanks for the input, Dave.
Been looking around and, they're a non-stocked item, like you said, or
they're big $$.
I have a bunch of much shorter, snap-in caps, which I've used in the past
with good success. They're 470 MF @ 450 VDC and 105 degree rated. Same
dia as these, but only about 40% of the height. Already have a PC board
made up for using 10, but easy to cut the board down to 8 to make it fit
the PS case. If I need to make a step start, I'll have plenty of room
above the new caps where I can place it. Probably an area of about 4 x 4
x
8 inches will be available.
I may just make the time and do it my self.
Having parts on-hand makes it much better than $200 on exact fit
replacements.
73 de Steve, NR4M
On 10/10/2014 19:09, David Harmon wrote:
Availability is probably going to be the problem....
Check with Ten-Tec....if they no longer use them...ask for a
recommendation.
Check with Henry Radio....they still have screw terminal lytics.
Recently I serviced a Henry 3KD with screw terminal caps from Henry.
73
David Harmon
K6XYZ
Sperry, OK
-----Original Message-----
From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Steve NR4M
Sent: Friday, October 10, 2014 12:43 PM
To: Amps
Subject: [Amps] Source for replacement PS caps
Hello all,
Figured it was time to re-cap the PS for my Ten-Tec since they are about
25 years old. The amp hasn't been used in a while so you just know what
will happen if I DON'T re-cap it before I use it.
I really don't want to change (mechanically) the way the originals are
mounted in order to use a different, possibly more available, cap.
Looking for suggestions on sources other than the 'usual' (Digikey,
Mouser,
etc...)
These caps are 400 MFD x 450 VDC, 85 degree, with screw terminals on
top.
Terminals appear to be #10, with a 1/2 inch spacing. Dia is 1 3/8 inch
and
length is 5 5/8 inches, or so.
100 degree would be nice and the capacity can be +/-.
Any input would be helpful. I just don't want to pay $25 per cap if I
can
find similar for $15.
--
73 de Steve, NR4M
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
--
73 de Steve, NR4M
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4765 / Virus Database: 4040/8362 - Release Date: 10/10/14
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|