Hi gang
Here’s a response I made to a question from my friend Paul W9AC. Paul
and I
have known each other for years, and he is a very savvy, technically
competent ham (as you probably already know). I hadn’t intended on
sharing
this exchange with the List because it’s pretty technical, but I’m
happy
to go do so.
73,
Jim w8zr
Sent from my iPhone
Begin forwarded message:
*From:* Jim Garland <4cx250b@miamioh.edu>
*Date:* December 19, 2020 at 5:14:17 PM MST
*To:* Paul Christensen <w9ac@arrl.net>
*Subject:* *Re: [Amps] W8ZR Autotune Amplifier Progress Report*
Good question, Paul. I'm using five of the eight available
microprocessors, or "cogs" as Parallax calls them. Currently, COG0
is the
"base" cog, which manages the entire program and offloads chores to
other
cogs when necessary or convenient. I've loaded COG0 with some chores
I'll
eventually direct elsewhere. For example, at the moment when RF at
the amp
input is detected and authenticated (to verify it's in a valid range,
that
the amp is on-line, etc.), then the bandswitch, tune, and load caps are
moved sequentially. That works fine for the tune and load caps, since
they
adjust in a fraction of a second, but depending on circumstances, the
bandswitch may take a couple of seconds. My plan is to move that
tuning to
other cogs so the three steppers readjust simultaneously. Ditto for the
initialization routine which zeros the steppers at power up and
starts the
warmup countdown. I want to add some timing features to a dedicated
timing
cog, COG2, along with an intelligent power up and power down routine for
blower control and temperature measurement. All COG2 does now is count
seconds and blink an LED to tell me the circuit is working.
COG7 is dedicated to computer interfacing. It outputs and inputs serial
data to a USB port, which is used to download firmware into the
Propeller
and to display messages and data onto a PC monitor. It also controls the
4-line LCD, as shown on the YouTube video.
COG 1 is dedicated to manual tuning, including managing the
band-stacking
register. Implementing manual tuning turned out to be my hardest
programming challenge. Reading and updating memory when the tuning
buttons
were pressed, along with the Save feature, interfacing manual tuning
with
autotuning so the two modes didn't fight each other, etc., took a
couple of
months to work out.
COG3 is a system frequency counter, which runs all the time. It detects
and measures RF at the amplifier input with a sensitivity of 250uV and a
resolution of 1 kHz, then passes the measurement as a variable to COG0
which makes sure the frequency is in a valid ham band. The frequency
counter works better than I expected. I initially had planned to use a
Schmitt trigger to clean up the input RF, but didn't need to do that. I
measure every signal twice, with measurements spaced out 100mS, and
require
both measurements to agree before deciding the result is valid.
I made a design decision early-on not to arbitrate or control QSK and
ordinary T/R switching. There's plenty of spare capacity in the
Propeller
to do that, as well as to measure RF power, SWR, plate voltage and
current,
grid current and safety trip features, but for now I'm not going down
that
road. Most of these extra functions are easily controlled with
standard or
dedicated circuitry (e.g., we each have our own QSK designs) and already
exist in commercial amplifiers. By avoiding them in this project,
it's easy
for other builders to use the Propeller as an add-on to existing
amplifiers. All that's really needed is to sample the RF at the input of
their amplifier, and mechanically connect stepper motors to the
switch and
variable capacitor shafts. It's tempting to look at all the available
programming space and start adding features, but for now anyway I
want to
make the project as easy to implement as possible!
I hope to start laying out a PCB based on my breadboard within the next
week or so. The basic circuit seems to work well, so I don't foresee any
major problems lurking in the shadows. Famous last words, probably.
73,
Jim W8ZR.
On 12/19/2020 3:12 PM, Paul Christensen wrote:
"The PX32A is a sophisticated device containing eight fully independent
32-bit microprocessors that share 31 read/write IO ports and a common
memory
for storing variables.
Jim, what amplifier functions are being divided across the eight
independent
microcontrollers? For example, does one exclusively manage the T/R
function? Perhaps another is dedicated to monitor power supply
parameters,
etc.?
My 8877 amp uses an Arduino Mega 2560 but I cram the code for all
functions
into one loop. To make this work with one microcontroller, delay
commands
are invoked by comparing time registers. The main loop never stops
running
at full speed no matter what delays are present.
Within the constraints of memory, it's possible to load unrelated
programs
into the same microcontroller.
Paul, W9AC
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps