I have some updates on the Henry amp(s) I picked up and thought some of you may
find the results interesting. Maybe some of you can help with some of the
issues that remain.
I picked up Henry 3K Ultra head SN 65-171 and its mate, the SN 65-171 RF deck.
Along with those two pieces came an additional RF deck; Henry SN 65-104 that
was still in the Henry crate. I brought all three of these components back in
my 2005 Honda pilot. Left Wisconsin on Sunday morning at 6 am then on to
Prescott AZ and back home on weds at 3pm. Once home, I had two other guys help
me up the steps with the 250# consoles to my ham shack where I would dig into
the amps.
I did a visual inspection of the head and both RF decks. The -171 RF deck had
a damaged doorknob cap but looked ok other than that. Replaced 50pf doorknob.
Afterward, I plugged the -171 head into the -171 RF console, put on my safety
glasses and headphones in case there were any loud surprises. Fire extinguisher
on standby. I flipped the mains switch on the console and pushed the POWER
button on...the amp jumped to life and a flurry of ceramic chunks started
flying everywhere. Hmmmm. I took the RF deck out of the console and found
ceramic debris everywhere. I found the culprit...it was toroid across the tube
that was loose due to its damaged ceramic standoff insulator. RF Parts came
through on that and I was able to install the new ceramic standoff and resolder
the toroid. All servo motors and tuning working well.
The only issues I have with this -171 RF console are:
* HV and Filament voltages are high. Eimac says 5500V max at 6.3 on the
filament. Henry implies voltage on the plate at 3800 CW/4800V SSB or so and
the filament voltage at 6.3. Mine are at 5500V and 7.0V respectively. With
243VAC coming into the shack I will be re-tapping the plate transformer to
5000V and filament closer to 6.3v.
* When repaired, I put this amp on the air and noted a severe problem with
the degradation of the incoming signal when the amp was ON. With the amp
idling, I can copy a strong, clear station and within seconds the signal begins
to get scratchy and eventually gets so bad the signal is unreadable.
Eventually the band signals disappear on the scope. A simple tap of a CW key
brings everything back into clear reception for another 8-10 seconds before the
signal degrades again. This is happening on all bands. Checked and cleaned
input/output connections. Reseated tube as well as removed and inspected bird
element connections. Same problem. It could be the crappy little guardian
input relay Henry used to switch in the incoming RF? I have to pull the RF deck
again and flip it over to see if I can pull and re-seat that relay. Suggestions?
After that exercise, I pulled the -104 RF console out of the crate and plugged
it into the -171 control head. I flipped on the wobbly AC mains switch and
nothing... After some quick inspecting I found the mains circuit breaker
broken. It appears it was smashed when it was placed into the crate. I found
a replacement Heinmann 40A breaker and installed that. Then I threw the switch
and the amp came to life. This amp had not seen voltage since 1994...that was
the date on the shipping crate sent from Henry to General Dynamics in SoCal. I
saw 6.3 on the filament and 3800 CW/4900V SSB on the multimeter so I left the
amp on to cook and walked away for 24 hours. Returning to the shack all seemed
well and I applied some RF to the amp. Working like a champ. 70 watts in gets
1800 into the dummy load.
So, as it sits now I am in need of some advice as to why I see the signal
degradation with the first RF console. I plan on yanking the RF deck this
weekend to flip it over to see if I can see anything obvious.
I also need to know a source for the small push in bulbs Henry used for their
indicator lights. No cross reference in my Ultra or 3KA manuals
Thanks in advance for any help you can provide.
More soon
Carl W9LF
From: Carl Braun
Sent: Saturday, October 21, 2023 3:49 PM
To: amps@contesting.com
Subject: Starting up a NEW Henry amp
I'm headed out tomorrow am on my way to save a Henry 3K Ultra amplifier. I'm in
Wisconsin and the amp(s) is in Arizona. My buddy has gotten out of ham radio
years ago and still has this Henry 3K Ultra. He also has a second RF console
that came with it that has never been out of the crate. All of the hardware was
originally sold to General Dynamics in southern California. The crates console
still has the paper tag on it that shows delivery from Henry to Gen Dynamics.
My plan is to get the amp and extra console back home and get them back on the
air. I don't see myself doing anything other than plugging them into 240vac,
turn them on individually and letting the tube go thru a gettering process for
a day or so. These are 3cx1200D7 tubes with a controller that displays plate
and filament voltage so I can quickly see if anything is awry.
Any other suggestions from the group on starting these amps up?
Carl W9LF
Get Outlook for iOS<https://aka.ms/o0ukef>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|