This is by far the best subnet calculator I have used ands it free :)
http://www.wildpackets.com/products/ipsubnetcalculator
Sincerely
Tony Morella
Demarc Technology Group
Office: 908-996-7995
Cell: 908-246-9170
Fax: 908-847-0202
email: tony@demarctech.com
http://www.demarctech.com
Wireless Solution Provider
-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
On Behalf Of Bob Hrbek
Sent: Friday, May 24, 2002 10:57 AM
To: karlnet@WISPNotes.com
Subject: Re: [Karlnet] More routing questions
works in windows...It should extract to your c:\program files\3cipcacl
dir.
-bob
----- Original Message -----
From: "Dan Metcalf" <danm@suncorstainless.com>
To: <karlnet@WISPNotes.com>
Sent: Friday, May 24, 2002 9:24 AM
Subject: RE: [Karlnet] More routing questions
> Make sure you have a subnet calculator
>
> Dan Metcalf
> Wireless Broadband Systems
> dan.metcalf@wbsysnet.com
> 781-658-2075
> www.wirelessbroadbandsystems.com
>
> -----Original Message-----
> From: Norm Young [mailto:npyoung@applegatebroadband.net]
> Sent: Friday, May 24, 2002 10:24 AM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] More routing questions
>
> Sounds like interesting stuff, but how to get started? Can anyone
recommend
> a good book on routing?
>
> Thanks,
>
> Norm
>
>
>
> ----- Original Message -----
> From: "Bob Rohr" <brohr2@netzero.com>
> To: <karlnet@WISPNotes.com>
> Sent: Friday, May 24, 2002 12:24 AM
> Subject: Re: [Karlnet] More routing questions
>
>
> > Have you tried to breakdown the class c addresses into different
> > subnets? Example:
> >
> > 10.10.10.1 subnet mask of 255.255.255.252 on one interface, this
> > gives you 2 usable hosts. then subnet the rest of the ips into the
> > groups that you want. Example: 10.10.10.4 255.255.255.192 this
> > creates another network 62 usable host which you should be able to
> > pass thru another interface without causing ip conflicts. With
> > every subnet you essentially are creating networks inside of the
> > class c network that you should be able to route thru different
> > interfaces..
> >
> > Bill Fisher wrote:
> >
> > >
> > >If I have an entire class-c passed to a router, can I not assign
> > >the
> router
> > >an IP address of say 10.10.10.1 / 30 and then add an indirect route
> > >of 10.10.10.32 / 128 through another interface?
> > >
> > >I seem to only be able to break the Class-C in two chucks.
> > >
> > >bill
> > >
> > >_______________________________________________
> > >Karlnet mailing list
> > >Karlnet@WISPNotes.com
> > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > >
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
|