I have seen this in the past, I just needed to reload the s/w on the
board
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Jayson Baker
> Sent: Sunday, December 28, 2003 9:06 AM
> To: 'Karlnet Mailing List'
> Subject: RE: [Karlnet] KN-100 problems?
>
> None of the three function.
> Does not initialize the PCMCIA cards at all.
> Loading the SG-4000 license.
> When opened in the Configurator, doesn't even show PCMCIA at all -
just
> eth.
> Nor does it show "Empty PCMCIA"
>
> Regards,
> Jayson A. Baker
> Peak Internet Solutions
>
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Kevin Knuth
> Sent: Sunday, December 28, 2003 6:10 AM
> To: 'Karlnet Mailing List'
> Subject: RE: [Karlnet] KN-100 problems?
>
> Jayson,
>
> We do a quality control check on our boards. I am concerned when you
> say you have had more bad boards than you can count! Our return rate
> has been VERY low (less than 1% I believe).
>
> But to clarify- you say you bought 3 boards, but NEITHER will
initialize
> the cards. Does that mean ONE board did?
>
> What software have you loaded on the units?
>
> I take it you can bring up the software image in the configurator-
Does
> it even SHOW a PCMCIA interface? Does it show it as a wireless card?
>
> Kevin
>
> **************************************
> Kevin R. Knuth
> Business Development Manager
> North America
> 260-424-9690 Regional Office
> 614-822-5275 Corporate Office
> kknuth@karlnet.com
> www.karlnet.com
> **************************************
>
>
>
>
>
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
> [mailto:karlnet-bounces@WISPNotes.com] On Behalf Of Jayson Baker
> Sent: Saturday, December 27, 2003 6:41 PM
> To: karlnet@WISPNotes.com
> Subject: [Karlnet] KN-100 problems?
>
>
> Hi,
>
> We have three KN-100 boards purchased from two different distributors
> over
> the past two weeks.
>
> Neither of which initialize the cards in the slot (tried Lucent
Silver,
> Orinoco Silver, YDI Sapphire).
>
> When we login w/ the Configurator all it shows is an Ethernet
interface.
> Looks like it doesn't even see PCMCIA.
>
> Tested all these cards in a KN-200 we have, they all work fine - not
the
> cards.
> Changed the jumper from 3.3V to 5V - that's not the problem.
> Done a reload on all boards numerous times - again, not the problem.
>
> Anyone else having these problems? Bad batch of KN-100 boards. again?
> Don't they run ANY of these through ANY sort of QC? I can't count the
> number of boards we've received DOA.
>
> Anyone's input is greatly appreciated as KN is out until Monday I'm
sure
> (and we need a board for Monday morning!)
>
> Regards,
> Jayson A. Baker
> Peak Internet Solutions
> Phone: (719) 686-1490
> Facsimile: (719) 686-1864
> E-Mail: jbaker@peakinet.net
> Web: http://www.peakinet.net/
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> --
> [This E-mail scanned for viruses by Declude Virus]
--
[This E-mail scanned for viruses by Declude Virus]
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|