Even more testing:
Snapshot of Winkey communication log with PTT enabled and toggling Ctrl:
(PTT LOCK-UP)
> 0004104277: Log enabled, (urouter v7.7.1)
> 0004104401: H-TX: 15 [Request WinKey Status]
> 0004104433: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004104448: H-TX: 07 [Get Speed Pot]
> 0004104479: H-RX: 8B [speed: min+11=21WPM]
> 0004105899: H-TX: 15 [Request WinKey Status]
> 0004105930: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004105946: H-TX: 07 [Get Speed Pot]
> 0004105993: H-RX: 8B [speed: min+11=21WPM]
> 0004107397: H-TX: 15 [Request WinKey Status]
> 0004107428: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004107459: H-TX: 07 [Get Speed Pot]
> 0004107490: H-RX: 8B [speed: min+11=21WPM]
> 0004108910: H-TX: 15 [Request WinKey Status]
> 0004108925: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004108957: H-TX: 07 [Get Speed Pot]
> 0004109003: H-RX: 8B [speed: min+11=21WPM]
> 0004109253: H-TX: 09 04(05) 18 01 [Set Pin Config: Pin5PTT=0(1),
> Pin5SideTone=0, Pin3KeyOut=1, Pin5KeyOut=0, HangTime=1.0wordspace,
> Priority=normal] [PTT On/Off: on]
> 0004115992: H-TX: 09 05 [Set Pin Config: Pin5PTT=1, Pin5SideTone=0,
> Pin3KeyOut=1, Pin5KeyOut=0, HangTime=1.0wordspace, Priority=normal]
> 0004115992: H-TX: 15 [Request WinKey Status]
> 0004116039: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004116055: H-TX: 07 [Get Speed Pot]
> 0004116086: H-RX: 8B [speed: min+11=21WPM]
> 0004117599: H-TX: 15 [Request WinKey Status]
> 0004117630: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004117661: H-TX: 07 [Get Speed Pot]
> 0004117693: H-RX: 8B [speed: min+11=21WPM]
> 0004119112: H-TX: 15 [Request WinKey Status]
> 0004119143: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004119159: H-TX: 07 [Get Speed Pot]
> 0004119190: H-RX: 8B [speed: min+11=21WPM]
> 0004119549: Log disabled, (urouter v7.7.1)
Snapshot of Winkey communication log with Semi Break-in enabled and
toggling Ctrl:
(NO PTT LOCK-UP)
> 0004441223: Log enabled, (urouter v7.7.1)
> 0004442019: H-TX: 15 [Request WinKey Status]
> 0004442050: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004442066: H-TX: 07 [Get Speed Pot]
> 0004442112: H-RX: 8B [speed: min+11=21WPM]
> 0004443516: H-TX: 15 [Request WinKey Status]
> 0004443532: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004443579: H-TX: 07 [Get Speed Pot]
> 0004443594: H-RX: 8B [speed: min+11=21WPM]
> 0004445014: H-TX: 15 [Request WinKey Status]
> 0004445045: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004445076: H-TX: 07 [Get Speed Pot]
> 0004445108: H-RX: 8B [speed: min+11=21WPM]
> 0004446184: H-TX: 09 04(05) 18 01 [Set Pin Config: Pin5PTT=0(1),
> Pin5SideTone=0, Pin3KeyOut=1, Pin5KeyOut=0, HangTime=1.0wordspace,
> Priority=normal] [PTT On/Off: on]
> 0004450583: H-TX: 09 05 [Set Pin Config: Pin5PTT=1, Pin5SideTone=0,
> Pin3KeyOut=1, Pin5KeyOut=0, HangTime=1.0wordspace, Priority=normal]
> 0004450599: H-TX: 15 [Request WinKey Status]
> 0004450630: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004450646: H-TX: 07 [Get Speed Pot]
> 0004450677: H-RX: 8B [speed: min+11=21WPM]
> 0004452206: H-TX: 15 [Request WinKey Status]
> 0004452237: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004452252: H-TX: 07 [Get Speed Pot]
> 0004452284: H-RX: 8B [speed: min+11=21WPM]
> 0004453703: H-TX: 15 [Request WinKey Status]
> 0004453734: H-RX: C0 [status: WAIT=0, KEYDOWN=0, BUSY=0, BREAKIN=0,
> XOFF=0]
> 0004453766: H-TX: 07 [Get Speed Pot]
> 0004453781: H-RX: 8B [speed: min+11=21WPM]
> 0004454780: Log disabled, (urouter v7.7.1)
That's my lot you will be pleased to note!
Regards,
Mike VP8NO
On 06/07/2011 13:18, Raymond Phillips wrote:
> Hi Paul
> My problem still exists.
> The setup I an using is WinXP SD V15.45 with rig control KENWOOD TS480 and
> winkey, as I said earlier the minute you hit Ctrl the rig goes into TX and
> stays there you have to shut the program down for it to go back to RX.
>
> On my other rig ICOM it works fine no problems.
> Anyone using Kenwood with the same problem or is it at my end.
>
> Rgds Raymond GM0VRP
> _______________________________________________
> SD-User mailing list
> SD-User@contesting.com
> http://lists.contesting.com/mailman/listinfo/sd-user
>
_______________________________________________
SD-User mailing list
SD-User@contesting.com
http://lists.contesting.com/mailman/listinfo/sd-user
|