TenTec
[Top] [All Lists]

Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects O2v2.032!

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects O2v2.032!
From: "Carl Moreschi" <n4py@arrl.net>
Reply-to: Carl Moreschi <n4py@arrl.net>,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 18 Apr 2006 23:11:42 -0400
List-post: <mailto:tentec@contesting.com>
If you are going to transmit on VFO B, the mode must be the same on the main
and sub receiver.  There is definitely a bug a here.

Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message ----- 
From: "Lin Davis" <linbdavis@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, April 18, 2006 9:59 PM
Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects O2
v2.032!


> Orion operators, be careful if you assign TX to VFO B.
>
> Like Randy, I also found a TX frequency error, 1500 Hz worth, on my Orion
II v2.032.
>
> My setup:
>
> On 40 meters:
> Assign TX and SubRX to VFO B.
> Assign RX to VFO A.
> Set MainRX mode to LSB.
> Set SubRX mode to LSB.
>
> Using an independent receiver to listen to the output, I pressed TUNE, and
zero
> beat the tx signal. I spoke into the microphone (connected to front panel
conn.)
> and heard my voice right on frequency.
>
> Then I changed MainRX mode to LCW.
>
> Pressing TUNE, I noted that the TX frequency did not change from above.
But when
> I spoke into the microphone, my speech was unintelligible. I had to tune
the
> receiver 1500Hz down to hear my voice normally!
>
> BTW, Randy's scenario was as above but with SubRX mode set to USB and Main
RX to
> LCW.
>
> I checked and found that the shift isn't dependent on sidetone setting.
>
> I didn't check previous code versions.
>
> When I get a chance I'll try other combinations.
>
> 73,
> Lin
> WB1AIW
>
>
>
>
> Randy, K4QO, wrote:
>
> > Condition:
> > VFO A is on 30 meters LCW mode
> > VFO B is on 60 meters USB mode.
> >
> > Result:
> > VFO B receives on frequency but transmits 500Hz low of frequency
displayed.
> >
> > If VFO A is then changed to USB mode (and no other changes),  then VFO B
> > transmits on frequency displayed.
> >
> > 73,
> > Randy
> > K4QO
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>