I've emailed direct to all who have requested a copy of the Corsair II QSK
(all modes) modification.
The mod for 561s is at http://tentecwiki.org/doku.php?id=561
The mod for 560s is at http://tentecwiki.org/doku.php?id=560
You should be able to save the PDF to your local hard drive for closer
review and or printing.
Mod requires cutting one wire and extending ends to a pair of RCA jacks.
Best regards,
Gary - AB9M
CSM(r) G.L.Huber
9679 Heron Bay Road
Bloomington, Illinois 61704
(309)662-0604
www.csm-gh.com
csm-gh@www.csm-gh.com
gary.huber@us.army.mil
ab9m@arrl.net
www.csm-gh.com/mytrike.htm
www.csm-gh.com/75thRepoDepo.htm
----- Original Message -----
From: "Rick" <rick_n4re@yahoo.com>
To: <ab9m@arrl.net>
Sent: Tuesday, January 01, 2008 9:39 PM
Subject: Fw: [TenTec] Corsair II & Titan 425
> Well, I finally got far enough up in the list to see that it was posted on
> the wiki. I got it, thanks.
>
> Rick - N4RE
>
> ----- Forwarded Message ----
> From: Rick <rick_n4re@yahoo.com>
> To: ab9m@arrl.net
> Sent: Tuesday, January 1, 2008 10:13:56 PM
> Subject: Re: [TenTec] Corsair II & Titan 425
>
>
> I'd sure like to see that QSK mod too. If you get a chance please send
> me a copy at n4re@arrl.net. I use a Corsair II and a Titan amp but
> usually only use the amp on SSB so never thought much about it on CW.
>
> TKS,
>
> Rick - N4RE
>
> ----- Original Message ----
> From: GARY HUBER <glhuber@msn.com>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Sent: Tuesday, January 1, 2008 10:19:15 AM
> Subject: Re: [TenTec] Corsair II & Titan 425
>
>
> My Corsair II also has the TX EN & TX OUT jacks (with jumper). Built in
> the
> "last run" of Corsair IIs... but I made the "QSK mod" and used it with
> my
> Titan 425. I have an Adobe PDF copy of the Corsair QSK mod. Email me if
> you
> want a copy.
>
>
> Best regards,
> Gary - AB9M
> CSM(r) G.L.Huber
> 9679 Heron Bay Road
> Bloomington, Illinois 61704
> (309)662-0604
> www.csm-gh.com
> csm-gh@www.csm-gh.com
> gary.huber@us.army.mil
> ab9m@arrl.net
> www.csm-gh.com/mytrike.htm
> www.csm-gh.com/75thRepoDepo.htm
>
>
> ----- Original Message -----
> From: "Bill Cotter" <n4lg@qx.net>
> To: "Carl Moreschi" <n4py@arrl.net>; "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Monday, December 31, 2007 4:24 PM
> Subject: Re: [TenTec] Corsair II & Titan 425
>
>
> > Carl, et al,
> >
> > I had a late model Corsair-II that had the tx-en and the tx-out
> > jacks for connection to the Hercules and Titan series. It was
> > factory installed and I have only heard of one other owner with the
> > same. You had to use the dual-pin jumper with it when not using the
> > amp.
> >
> > If you wish to see how TT came up with the signals, you might try
> > to find an owner with a late manual revision that includes tx-en
> > and tx-out.
> >
> > 73 bill n4lg
> >
> > At 07:46 PM 12/30/2007, you wrote:
> > >No. QSK and Ext T/R are very different. The corsair never had
> > >the TXOut
> > >and TXEn lines on it, which are required for a QSK amp. What you
> are
> > >supposed to do is connect Ext T/R to the amplifier keying
> > >line. This will
> > >not give you QSK but it will work with the amp that way.
> > >
> > >Another completely different approach is to connect your keyer
> output
> > >directly to where TXOut would have been connected to the
> > >amp. Then connect
> > >the output keying line of the amp to key the corsair. This will
> > >give you
> > >QSK and guarantee that the amp keys before the corsair transmits.
> > >
> > >Carl Moreschi N4PY
> > >121 Little Bell Drive
> > >Bell Mountain
> > >Hays, NC 28635
> > >----- Original Message -----
> > >From: "Gary Smith" <Gary@doctorgary.net>
> > >To: <tentec@contesting.com>
> > >Sent: Sunday, December 30, 2007 7:37 PM
> > >Subject: [TenTec] Corsair II & Titan 425
> > >
> > >
> > > > Am sending the Omni V to TenTec for allignment. Not sure of the
> > > best
> > > > way to connect my back up rig (Corsair II) to the amp for QSK.
> > > >
> > > > With the Omni V I connected the TX out & TX en to their
> > > counterparts
> > > > on the 425. I see no TX out or TX en on the Corsair but there
> > > exists
> > > > QSK and EXT T/R connectors on the Corsair. Are these the same
> > > > function but different names? I do want to use QSK.
> > > >
> > > > Thanks,
> > > >
> > > > Gary
> > > > KA1J
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > >_______________________________________________
> > >TenTec mailing list
> > >TenTec@contesting.com
> > >http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
>
>
>
>
> ____________________________________________________________________________________
> Never miss a thing. Make Yahoo your home page.
> http://www.yahoo.com/r/hs
>
>
>
>
>
>
> ____________________________________________________________________________________
> Be a better friend, newshound, and
> know-it-all with Yahoo! Mobile. Try it now.
> http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|