Need link to un subscribe from list. Any help appreciated
Get Outlook for Android<https://aka.ms/ghei36>
________________________________
From: Topband <topband-bounces@contesting.com> on behalf of John Harden, D.M.D.
<jhdmd@bellsouth.net>
Sent: Thursday, November 15, 2018 5:53:14 AM
To: JC; jim@audiosystemsgroup.com; topband@contesting.com
Cc: lee@k7tjr.com
Subject: Re: Topband: 40m array as RX antenna
I have one of JC's Waller Flags on a 40 foot boom at 95 feet.. It is fed
with LMR-600 at the tower base XFMR where the 100 ohm twin-ax
terminates. It is use with a K-3 in diversity receive with a Hi-Z 8
which is down the hill es across the creek. The system hears remarkably
well.. Beverages, Ewes, and other RX antennas are out the door...
In the shack the 40 dB N4IS pre-amp is in a steel box for shielding
purposes. All components of the station are connected via 1/2 " braid
to a 6 ' x 6" x 1\4' aluminum grounding bus.
There are multiple chokes in the leads per N4IS es NX4D... It has been a
long process.
The IC-7610 is also in use from time to time since this SDR radio is
Ultra-Quiet...
73,
John, W4NU
On 11/15/2018 7:19 AM, JC wrote:
> Hi Jim and Lee
>
>
> Before we agree that we disagree, let me elaborate on few basic concepts for
> a good design. Point by point and let me know which one you disagree.
>
> 1- RF runs outside the cable surface, it does not matter what is inside, a
> coax cable shield, a solid # 4 wire external surface is similar to a RG58 in
> respect of RF current.
>
> 2- Every cable on your station is an antenna. If the cable is 1/8 to 1/2 wave
> long on low bands, the energy on the outside surface is very high. 100ft
> rotor cable , or 100ft 9913 from your 2m antenna, or 100ft of controls cable,
> and or 100ft of RG6 on your RX antenna have almost the same energy of your
> 160m inverted L ~ 120ft.
>
> 3- All these cables somehow are connected to your station ground at your
> station. All of them are part of your antenna system and interact with each
> other.
>
> 4- Any of these cables connecting into a well-designed board brings a lot of
> energy on low bands, normally called common mode noise, signal that we don’t
> want to mix with our RX signal coming from our RX antenna.
>
> 5- Prevent the external RF current to enter into our board is a big problem
> on low bands. On Audio, you have an excellent description of pin 1 problem on
> your papers, 60 and 120 Hz is the issue. On low bands 1.8 MHz, all RF signals
> from 50 KHz to 10 MHz are responsible for the common mode noise current on
> low band antennas.
>
> 6- To filter or decouple 1.8 MHz signal a 1000 pf or 1nF has a very high
> impedance, 10nF is not enough, it is necessary 100 nF or more. DC filter is
> an issue too, it is easy to inject the common mode noise into the Vcc.
>
>
> 7- May point is that is very difficult to protect any board or parts, like a
> BALUN or transformer, or any amplifier from common mode noise, PIN 1 PROBLEM.
> A plastic box make almost impossible to avoid that. A Metal case protects
> the board and avoid the external current to get into the board.
>
> 8- I can agree that the intensity of the signal and the common mode signal
> leak could be 20 db, 30 db or more. However when you dig a weak signal it is
> huge problem.
>
> 73'
> JC
> N4IS
>
>
>
>
>
>
> -----Original Message-----
> From: Jim Brown [mailto:jim@audiosystemsgroup.com]
> Sent: Wednesday, November 14, 2018 8:10 PM
> To: n4is@n4is.com
> Cc: lee@k7tjr.com
> Subject: Re: Topband: 40m array as RX antenna
>
> On 11/14/2018 4:41 PM, n4is@n4is.com wrote:
>> I would suggest a metal box to protect any RX system, it does help.
> Only if the circuit layout is poor. Lee is right - shielding of circuity is
> only a band-aid for poor design.
>
> 73, Jim K9YC
>
> _________________
> Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
|