Towertalk
[Top] [All Lists]

[Towertalk] The School of Hard Knocks - Long

To: <towertalk@contesting.com>
Subject: [Towertalk] The School of Hard Knocks - Long
From: djl@andlev.com (Dan Levin)
Date: Tue, 2 Jul 2002 19:10:01 -0700
This true story may help others to avoid trouble in 
the future.  It may also bore you - my apologies in 
advance :-)

About a year ago, we bought a cabin in northern 
California on a site with a decent take-off towards 
the U.S.  I installed a 70 foot self-supporting tower 
with a 24 foot mast, and brought in a crane to mount 
a C-31XR at 72' and a 2 element 40 meter yagi that I 
designed at 80'.  The 2 element yagi uses capacity 
hats consisting of crossed 6' long .177" aluminum 
rods to shorten the elements by about 15% and to move 
the secondary resonance out of the 15 meter band to 
reduce interactions with the C-31.

A series of mistakes and bad decisions related to 
this project have cost me a bunch of trouble and time.

First of all, when I placed the hole for the tower 
base, I was a bit sloppy.  I didn't actually 
calculate the turning radius of the 40 meter yagi, I 
just picked a spot that looked to be about in the 
middle of the meadow, and dug the hole.  After the 
fact, I measured the distance from the hole to some 
nearby redwood trees, and decided that there was 
barely enough room.  I was wrong.

When we actually put the antennas up on the tower, it 
became clear that while they would probably clear the 
trunks of the trees, the 40 was going to get caught 
up in the branches of the redwoods.  No problem I 
thought, when I get a chance I will have a tree guy 
come in and trim the branches back.  Until then, I 
just won't rotate the antennas through the trees.  My 
second mistake.

I am always in a hurry when I am doing radio stuff, 
because my family isn't very patient with me.  When I 
put the antennas up, I put a 1/4" bolt through the 
mast at the rotor - but I didn't take the time to 
tighten the U-Bolts on the rotor-to-mast mount.  I 
meant to come back and do it the next day, but of 
course I forgot.  I figured at the time (incorrectly, 
as it turns out) that a 1/4" bolt was plenty strong 
enough "for now".

Of course, last winter a storm came through and broke 
the 1/4" bolt.  The antennas free-wheeled in the 
wind, and crashed into the redwood trees that I 
hadn't bothered to trim yet.  The capacity hat on the 
40 meter yagi got all bent up, and one spoke broke 
off of one hat.  Even with all that damage, the 
antenna still worked in the SSB segment, so I 
operated a bit this spring before the weather got 
good enough to fix the antenna.

Last weekend, I climbed the tower, rotated the 40 
meter yagi's boom so that the elements pointed up and 
down, climbed back down to the level of the lower 
tips of the elements, reached out from the tower with 
a 'gaff' and pulled each element tip in turn in to 
the tower so that I could bend the hat spokes back 
into place.  I figured the job would take me 3-4 
hours.

What I found was that the spokes were not only bent, 
but that the brazes that hold the spokes to the 
elements had broken.  Since I had operated with the 
hats in this damaged condition, they had arched and 
there was soot all over the element/hat joints.  I 
ended up having to remove each hat from the element 
(which means drilling out rivets at 55'), lower them 
to the ground, rebraze the spokes, raise them back to 
the tower, and reinstall them on the elements.  8 
hours into the mission, and I'm about 2/3's of the 
way done.  I expect to spend another 2-3 hours on the 
job this weekend.  What a mess.

So a sequence of poor decisions conspired to cost me 
over a day of heavy climbing work.  If I had placed 
the hole for the tower correctly, it wouldn't have 
happened.  If I had trimmed the tree as soon as I saw 
the problem, or if I had tightened the U-bolts on the 
rotor when I should have, it wouldn't have happened.  
If I hadn't put RF into a damaged antenna, I would 
have had an easier time because there wouldn't be 
soot all over the place.  It wasn't really any one 
thing - it took at least three mistakes to get me in 
trouble - but trouble I am in nonetheless.  Tall 
towers and big antennas are not very forgiving.  
Sloppy work costs you dearly, as I am learning the 
hard way.

If it wasn't for the invaluable help and education 
that all of you have provided me over the years, I 
could never have attempted this project in the first 
place.  I hope the story of my folly can help someone 
else avoid a similar fate.

              ***dan, K6IF



<Prev in Thread] Current Thread [Next in Thread>
  • [Towertalk] The School of Hard Knocks - Long, Dan Levin <=