Towertalk
[Top] [All Lists]

Re: [TowerTalk] Yaesu Rotator connector replacement - trailer-stylevs. A

To: <eric@k3na.org>, <ersmar@comcast.net>
Subject: Re: [TowerTalk] Yaesu Rotator connector replacement - trailer-stylevs. Amphenol Eco-Mate
From: "David Robbins K1TTT" <k1ttt@arrl.net>
Reply-to: k1ttt@arrl.net
Date: Fri, 2 Feb 2007 11:35:59 -0000
List-post: <mailto:towertalk@contesting.com>
Or just wrap once to insulate and then seal the whole splice in that
underwater heatshrink splice sealer stuff.


David Robbins K1TTT
e-mail: mailto:k1ttt@arrl.net
web: http://www.k1ttt.net
AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
 

> -----Original Message-----
> From: towertalk-bounces@contesting.com [mailto:towertalk-
> bounces@contesting.com] On Behalf Of Eric Scace K3NA
> Sent: Friday, February 02, 2007 02:47
> To: ersmar@comcast.net
> Cc: Rick Scott; towertalk@contesting.com
> Subject: Re: [TowerTalk] Yaesu Rotator connector replacement - trailer-
> style vs. Amphenol Eco-Mate
> 
> Hi Gene --
> 
>    Yep, we tried staggering the butt splices and wrapping the bundle,
> just like you did.  Water got between the loose wires of the bundle and
> under the tape.  And the whole splicing procedure was time-consuming and
> tedious.
> 
>    One could split out each wire separately, butt-splice it, and then
> wrap EACH butt splice separately with the three-layer method.  That
> would be even more time consuming.
> 
> -- Eric K3NA
> 
> on 07 Feb 01 Thu 21:09 ersmar@comcast.net said the following:
> > Eric et al:
> >
> >      I taped the only outdoor trailer light connector in my system - the
> one underneath the rotator base.  I,too, believed that that was a point
> for water ingress, so I took precautions.  The other two connectors are in
> a NEMA 3X enclosure and inside the shack so water shouldn't be a problem.
> >
> >      The wires that are molded into the Wireman's trailer light
> connectors (my source) are individual #12 or #14 gauge color-coded wires.
> I butt-spiced them onto the main, round rotator cable run at the three
> connector points.  But I staggered the lengths of the pigtail wires so I
> didn't have the splices aside of each other; rather, each splice begins at
> the end of the last one.  (PITA.)  When finished with the mechanical
> splices I wrapped the entire bundle in tape, although filled shrink wrap
> would have been better.
> >
> >      The eight-pin trailer connectors from the Wireman currently cost
> $8.25 ( http://www.thewireman.com/prodpix6.html .)  I certainly would urge
> adding tape to any outdoor connection where they are used.
> >
> >      Caveat Amateur.
> >
> > 73 de
> > Gene Smar  AD3F
> >
> >
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>