Forwarding again to reflector. Didn't see it post the first time.
-----Original Message-----
From: Keith Beebe W3KB
Sent: July 20, 2019 8:58 AM
To: Don Hill AA5AU <aa5au@bellsouth.net>; 'Writelog Reflector'
<writelog@contesting.com>; wk6i.jeff@gmail.com
Subject: RE: [WriteLog] save configuration
Jeff WK6I:
Save File will save that particular contest and the setup you did for that one
contest ONLY.
The Setup - Save Configuration does exactly that, it saves the standardized
configuration for the ENTIRE program.
I have one standard configuration that I like (using Setup - Save
Configuration) that comes up each time I open the program (using New Log) to
begin setting up for a new contest.
Then once I have that particular contest setup the way I want it, I then I
simply Save File. It saves that particular contest setup only.
There, I just saved you 99 times of using Save Configuration. Save your
standard configuration once, then simply open a New Log, setup for that
particular contest and just use Save only.
Keith W3KB
-----Original Message-----
From: WriteLog <writelog-bounces@contesting.com> On Behalf Of Don Hill AA5AU
Sent: July 20, 2019 8:28 AM
To: 'Writelog Reflector' <writelog@contesting.com>
Subject: Re: [WriteLog] save configuration
Good question but I don't know the answer. I can tell you I only do a Save
Configuration when I change something. When I start a new contest, I import the
messages, Save the file with a filename, do any other changes (add/delete/move
windows or change the keying port for CW or RTTY), do a Save Configuration, and
then Save the file again. From there I normally never had to make any changes.
Don AA5AU
-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Jeff Stai
Sent: Saturday, July 20, 2019 12:11 AM
To: Writelog Reflector
Subject: [WriteLog] save configuration
I've been using writelog since the turn of the century I think. There are some
things I do, because back when I learned how to get writelog to do what I
wanted it to do - and not get burned or lose things - those things just seemed
to work. It's almost like a ritual or incantation.
One of these things is save configuration. When setting up for a contest I bet
I do a save configuration 100 times. Every time I set a parameter or enable
something it's:
Save File
Setup
choose Save Configuration
click OK.
..because I don't want to lose what I have done and start over.
I have questions.
1. Why is save configuration still a tedious three click task? Why isn't it a
one click button like file save?
2. I'm going to guess the answer. It's because save configuration is actually
something you almost never have to do so why make a button for it.
Right?
3. If that is the case, then I must be doing save configuration about 99 times
too much...?
4. So then, what does save configuration really do?
73 jeff wk6i
--
Jeff Stai ~ WK6I ~ wk6i.jeff@gmail.com
RTTY op at W7RN
Twisted Oak Winery ~ http://www.twistedoak.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|