Hercules II amplifer (exc condition) brand new remote control head 10 meter mod board (not installed) 70 amp switching supply $1050 + shipping RX-320 receiver (3 weeks old) as new with all accessorie
As new, less than one month old $250 shipped in the lower 48 Thanks Tim NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.com Administrative requests: tentec-REQ
Looking for a VFO for a Triton IV please send condition and price if you have one for sale Thanks Tim NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.com Admin
I am putting an 8 pin plug back on a 244 digital readout, does someone have the wiring info, including what jumpers are needed on the plug.. Thanks in advance for any help. 73 tim NZ8J -- FAQ on WWW:
10 amp airpax circuit breaker, used with the Argosy I think.. $10 shipped thanks Tim NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.com Administrative request
Excellent condition Ten Tec Omni-C Station. all equipment is a 9 or better. Consists of: Omni 546 with WARC bands 500 hz CW Filter 1.8 KHZ SSB Filter Non-Ten Tec hand mic with Heil HC-5 element 255 S
Just picked up a very nice Triton IV, but there is one thing I wonder if anyone has run across. Even with the audio gain all the way down, the audio is still quite loud from the radio, the only way t
Thanks to all for the suggestions, it turned out to be the audio control pot, I replaced it and all is fine now.. 73 Tim NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@c
Anyone have a spare plastic strip that goes between the top cover and the front panel of a Triton 4? It is about a foot or so long and is slotted on both sides so the top of the front panel and the c
Looking for a mint Corsair II station with the remote VFO, power supply and filters. If you have one for sale please send all particulars as to the price, physical and electrical condition. Thanks Ti
Looking for both the 243 and 242 remote vfo's. Please send info if you have either one for sale thanks Tim NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.com
Would like to replace the small knob on my 540 with one of the larger ones that came with the later 540/544's anyone have a spare laying around they would sell? thanks tim NZ8J -- FAQ on WWW: http://
Sorry, forgot to say which knob.. it's the main tuning knob.. NZ8J -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.com Administrative requests: tentec-REQUEST@conte
I'll probably be sorry, I have decided to trade my 515 Argonaut (serial number 088) for a 100 watt Ten Tec radio. I would like to trade it for a Ten Tec 544 Digital with the noise blanker and cw filt
I have had several folks asking to buy the 515 station outright, a few initial offers to trade, but not many follow-ups, so I am offering it for $400 + shipping . It includes the 515, 208A CW/Notch f
The Argonaut 515 Station has found a new home.... Thanks Tim NZ8J -- FAQ on WWW: http://www.contesting.com/tentecfaq.htm Submissions: tentec@contesting.com Administrative requests: tentec-REQUEST@con
I have acquired a excellent condition KR-20A keyer that I do not need. It is a single paddle keyer that runs off ext 12vdc or 110vac. It has a silver face and black case. It works fine and I have the
Consists of: Ten Tec 544 Digital (Serial Number 2288) Noise Blanker CW Filter Ten Tec 242 Remote VFO Ten Tec 262M Power Supply All documentation The 544 and VFO were gone over by Ten Tec about a year
Just saw these on a swap board, looks like they could be a good deal.... just thought I would pass it on in case anyone was looking for one of these, I don't have any connection with the seller tim N