Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 16:07:18 -0500
Gents, Winmoor does not support the Omni 6 Plus in their Rig Control software. I'm thinking that someone once told me there was a different brand and model that used a command set equal to or very si
Author: Rod Greene via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 21:12:37 +0000 (UTC)
Joe, seems like I used Icom 735 (some older version like that) with my Paragon that has an N4PY chip. The Omni 6 may be the same GL es 73, Rod/w7zrc From: Joe Papworth via TenTec <tentec@contesting.c
It uses the Icom interface. Just select an Icom radio at the correct baud rate. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 3/2/2018 4:07 PM, Joe Papworth via TenTec wrote: G
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 17:38:15 -0500
Thanks Rod. I'll check it out. Later, Joe, K8MP Sent from AOL Mobile Mail Joe, seems like I used Icom 735 (some older version like that) with my Paragon that has an N4PY chip. The Omni 6 may be the s
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 17:44:44 -0500
Thanks Carl! Sent from AOL Mobile Mail It uses the Icom interface. Just select an Icom radio at the correct baud rate. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 <a href="http://www.n4py.co
Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus To: w7zrc@yahoo.com, tentec@contesting.com Cc: k8mp@aol.com Date: Friday, March 2, 2018, 5:38 PM Thanks Rod. I'll check it out. Later, Joe,
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 18:52:19 -0500
Thanks Greg, I keep muffin fans blowing on the rig's heat sink and power supply's heat sink most of the time already. Later, Joe, K8MP Sent from AOL Mobile Mail Subject: Re: [TenTec] Winlink and Winm
I used the Icom 735 with Signal Link with my Omni VI Plus. Jim K7IKN _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/list
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 21:57:49 -0500
Jim, et al, They must have removed the 735 from the list. It only shows newer models of Icoms. They do have two generic Icoms in the list: "Icom Amateur radios" and "Icom Amateur Radios (Early)" I ch
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 22:02:41 -0500
I meant to ask if the Signal Link is a necessity with Winmor. I'm using the serial cable for rig control and that set up keys the rig fine when I'm running MMTTY and FLDigi Joe, K8MP I used the Icom
The Omni VI does not have a keying interface. You would need to use a Winkey keyer for that. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com They must have removed the 735 from the
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Fri, 2 Mar 2018 22:32:26 -0500
Oh contraire Carl. I've been keying it thru the serial port using MMTTY and FlDigi.for a long time. The Omni VI does not have a keying interface. You would need to use a Winkey keyer for that. Carl M
Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus To: n4py3@earthlink.net, tentec@contesting.com Cc: k8mp@aol.com Date: Friday, March 2, 2018, 10:32 PM Oh contraire Carl. I've been keying i
Author: Joe Papworth via TenTec <tentec@contesting.com>
Date: Sat, 3 Mar 2018 08:53:10 -0500
Thanks Greg. I tried it when there was no activity and even went "Off channel" to see if that made a difference. I keep thinking it is an operational error though because the rig did accept the QRG a