Amps
[Top] [All Lists]

[AMPS] parasitic suppressors

To: <amps@contesting.com>
Subject: [AMPS] parasitic suppressors
From: measures@vc.net (Rich Measures)
Date: Tue, 16 Dec 97 17:22:19 -0800
>Rich Measures wrote:
>
>>K5GW (reproduced here with permission).
>>>>
>>>>I have lost many cathode zener bias diodes in my 2m 8877 amp over the years
>>>>(none since installing the 50ohm plate resistor). I always assumed that 
when
>>>>the plate arced to ground and by way of grounded grid, perhaps plate to 
grid,
>>>>that the HV power supply b plus was almost instantly placed at ground
>>>>potential. If this is the case, the B minus lead must also nearly instantly
>>>>rise to a negative value close to the full HV dc voltage less whatever 
amount
>>>>has been lost during the nearly instant period of time. This being the 
case,
>>>>the cathode is now negative several thousand volts compared to the still
>>>>grounded grid. Looks to me like a large current would flow in this case,
>>>>possibly damaging either/both cathode and grid. I know enough current 
flows to
>>>>blow the smithereens out of the grid meter!
>>
>>However, most builders protect the grid current meter shunt resistor with 
>>=>200a glitch diodes -- which also protects the grid current meter.  With 
>>glitch diodes, the peak potential across the grid current shunt R during 
>>an anode/grid arc would be roughly 1.5V -- which is not enough to blow 
>>the zener bias diode.  
>
>OK, we're nearly in agreement. However, if the grid current meter is
>damaged, it is clear that the shunt and/or the diode didn't do the job.
>
I have never seen 3A/200a-pk diodes fail to protect a grid current meter. 
 If the designer used flimsy diodes, which failed to protect the meter, 
that is a separate issue.  
... ... ... 

>Agreed that 1N540x diodes will usually work, but their 200A surge rating
>is strictly time-limited... and we don't actually know how long the
>surge will last. 

sure we do.  T=R*C.
>>
>>-  However, there seem to be some problems with the grid/anode arc 
>>theorum:  
>>1.  I have never seen a kaput 8877 grid bearing an arc mark.  
>>2.  No amplifier builder has reported finding one.  
>>3.  The reported arcs/'big bangs'  sound like an arc in the room.  Arcs 
>>in a near vacuum do not make a 'bang' sound.  For instance, an arc in a 
>>vacuum variable capacitor produces a faint 'tink' sound.  Bangs need an 
>>atmosphere.  
>>4.  Roughly 2/3 of the kaput 8877 grids I see have fairly uniform gold 
>>blistering around the circumference of the grid.  
>
>I agree about the 'tink' inside the tube, but the bang can come from the
>consequences in the circuit outside - like a meter being blown to
>smithereens (love that word!). 

-  The voltage across the tube is reportedly 50v.  It seems a bit of 
stretch to imagine that this could produce a secondary arc outside the 
tube that would produce a loud bang. 
-   People who use glitch diodes report 'big bangs'.  The meter is 
undamaged.  The diodes survive.   

>Also, arcs can take place outside the
>tube; 

Surely, which seems to be the case during some intermittent VHF/UHF 
parasitic oscillations.

>they are very common in VHF/UHF amps, probably because the output
>circuit often has the full DC on it as well as RF voltages.
>
>This side-topic is not so much about the causes of near-crowbar shorts
>from anode to chassis, but about design techniques for preventing damage
>when they happen.
>
There seems to be scant evidence to support the theory of an anode/grid 
arc causing damage to the grid.   Too many cathode bias zeners are 
shorting.  Too many parasitic suppressor resistors are being damaged - 
and not during 15m or 10m operation.  
... ... 
>...and uses a surge limiting resistor in the B+ supply, and rates
>everything to survive the fault condition with plenty in reserve.
>
- As I recall, there was an article in the January, 1994 issue of *QST* 
that proposed such things.  However, in the September, 1994 issue of 
*QST* there were some "experts" who did not agree.  
cheers
Rich...

R. L. Measures, 805-386-3734, AG6K   


--
FAQ on WWW:               http://www.contesting.com/ampfaq.html
Submissions:              amps@contesting.com
Administrative requests:  amps-REQUEST@contesting.com
Problems:                 owner-amps@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm

<Prev in Thread] Current Thread [Next in Thread>