Amps
[Top] [All Lists]

Re: [Amps] AM-6154 questions

To: <amps@contesting.com>, "Web Williams" <kr4wm@earthlink.net>
Subject: Re: [Amps] AM-6154 questions
From: "RICHARD GEORGE" <k6kwq@msn.com>
Date: Sun, 12 Sep 2004 12:17:27 -0700
List-post: <mailto:amps@contesting.com>
I would have never left it running for that long. This amp was only designed 
for 50 watts out. You probably overheated the cavity and after you left it off 
and it cooled down it now is making contact in the cavity. In my experience 
with these amps, leave the 8930 in place. You said you only wanted 150 watts. 
Did you note the difference in anode size when you changed the tube? 350 watts 
output is about the safe max on SSB. I know you here about 500 watts out, I can 
guarantee not for long, and it will sound terrible. I modified my last one by 
cutting the power supply away from the cavity and making it 2 pieces. Much 
easier to transport to mountain tops, and you can replace the noise maker 400hz 
fan with a bigger ac fan for more cooling. 
But again opinions  are like a## H#### every one has one.





K6KWQ Dick "12 Volt radios are for wimps, real radios can kill you" Still can't 
make it go QRO with "More Power"
  ----- Original Message ----- 
  From: Web Williams 
  To: amps@contesting.com 
  Sent: Sunday, September 12, 2004 10:58 AM
  Subject: [Amps] AM-6154 questions


  I thought I'd come in here begging for an answer, since I have not
  been able to turn up anything on the internet about an AM-6154
  VHF amplifier that I have.

  It's been working fine with an 8930 for about three years, but
  seeing all the improvements being raved about, I felt compelled
  to try a Svetlana 4CX-400. The tube swap was uneventful, as
  well as the tuneup with the new tube. Everything looked just
  fine! I was advised by the tube seller to "keep it down" for the
  first 24 hours or so, and he provided me with a procecure for
  tube burn-in. I had no way to do it the way he described, but
  he said alternately that I could leave the amp turned on for 24
  hours, and if there were any problems with the tube being gassy,
  or having a bad seal, it would likely show up.

  After checking for output (I did want to see if it was going to work)
  I tuned up at about 150 watts for a couple of watts in, and everything
  looked great! I assumed (hope I was correct) that this minimal power
  level would not really stress anything. I then left the amp turned on for
  24 hours to burn in.

  The next morning, I went to my shack, and checked everything, and it
  seemed just fine. Same 150 watts output (I had not tried to go for max
  smoke yet- I have an ARR preamp in line that is only rated for 160 watts
  pass-through). I heard a station on, and called him. My wattmeter is
  situated where I cannot see it when I am speaking into the microphone.
  After several unsuccessful calls, I looked over at the meter, and it was
  dead on zero when I was transmitting!

  I made an assumption that I blew the new tube, so I quickly put the
  8930 back in. Still no output (after retuning to proper positions on all
  dials).

  Both fuses on the front check good with my DVM. Plate voltage goes
  to mid-scale (not sure how this unit was set up, I didn't do it, and don't
  know who did). Screen voltage is 40 (about 3/4 scale) and grid voltage
  goes to 50 (not pegging the meter, but almost). Heater voltage puts the
  meter at 28. Still no output!

  I let the amp sit for about a week, went back to it, and still no output.
  Three weeks of sitting there without me even touching any controls
  I went back to it, and it's fine! Other than turning it on and checking the
  voltages by spinning the test switch through the various test positions, it
  seems perfectly OK! (Didn't put the 4CX400 back in it.)

  Does anyone have any ideas as to what to check? I'm totally lost!!!

  Thanks, -Web Williams in Myrtle Beach, SC


  _______________________________________________
  Amps mailing list
  Amps@contesting.com
  http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>