Rex Lint wrote:
> URL?
>
http://www.multi-tech-industries.com/rswitches.html
73
Roger (K8RI)
> -Rex-
>
> Rex Lint, Consultant
> 26 Brek Drive
> Merrimack, NH 03054
> PH: 603-860-7651
>
> -----Original Message-----
> From: Roger [mailto:sub1@rogerhalstead.com]
> Sent: Saturday, March 13, 2010 10:35 PM
> To: Carl
> Cc: Rex Lint; 'Paul Kraemer'; Amps
> Subject: Re: [Amps] Revamping a really ugly amp
>
>
>
> Carl wrote:
>
>> Multi Tech, formerly Radio Switch Corp, will build you a Type 86 switch to
>>
>
>
>> your hearts desire. And a lot cheaper than a litter of vacuum relays.
>>
>>
> Man! They have some nice looking switches!
>
> 73
>
> Roger (K8RI)
>
>> Carl
>> KM1H
>>
>>
>>
>>
>> ----- Original Message -----
>> From: "Rex Lint" <rex@lint.mv.com>
>> To: "'Paul Kraemer'" <elespe@lisco.com>; "Amps" <amps@contesting.com>
>> Sent: Saturday, March 13, 2010 4:36 PM
>> Subject: Re: [Amps] Revamping a really ugly amp
>>
>>
>> A variable inductor makes band changes too slow in contests (unless I make
>>
> 6
>
>> amps!)
>>
>> -Rex-
>>
>> K1HI
>> Rex Lint
>> Merrimack, NH
>>
>>
>> -----Original Message-----
>> From: Paul Kraemer [mailto:elespe@lisco.com]
>> Sent: Saturday, March 13, 2010 3:34 PM
>> To: Rex Lint
>> Subject: Re: [Amps] Revamping a really ugly amp
>>
>> Rex
>> I would keep the variable inductor as it represents an ideal situation for
>> an all band all mode amp, IMHO
>> In power rf smaller may not be better, IMHO
>> If I were going to use relays they would be vacuum type as are used in
>> commercial designs. I've seen it done at Collins Rockwell .
>>
>> Paul K0UYA
>> ----- Original Message -----
>> From: "Rex Lint" <rex@lint.mv.com>
>> To: "Amps" <amps@contesting.com>
>> Sent: Saturday, March 13, 2010 1:04 PM
>> Subject: [Amps] Revamping a really ugly amp
>>
>>
>>
>>
>>> I bought an old H/B amp that I'm totally revamping.
>>>
>>> It's 2 x 3-500Z's with a 4KV power supply. It USED to have a pi-network
>>> with a vacuum variable plate capacitor and a regular variable loading
>>> capacitor, and the tank coil *was* a variable inductor so that the tank
>>> could be adjusted for any transformation (within reason). I want to keep
>>> the caps, but change the coil to discrete inductor(s) with taps.
>>>
>>> I wonder if anyone uses relays instead of a rotary switch to select the
>>> desired taps? What are the parameters I need to consider in trying this?
>>> In my thinking, I'll just be switching the output side of the inductor,
>>> and
>>> the impedance at this point (when tuned) should be about 50 ohms, so the
>>> voltage isn't that high (350 V.?), and the current would be about 6
>>>
> amps.
>
>>> Relays for this should be a dime (well, $20) a dozen? As a mtter of
>>>
> fact,
>
>>>
>>>
>>
>>
>>> I
>>> see one like this would handle the job if never switched "hot" which you
>>> wouldn't want to do with a rotary switch either!
>>> http://www.mv.com/ipusers/lint/K1HI/RelaySpecs.pdf
>>>
>>> I'm also looking at compact tank coils in the literature. How much power
>>> could I expect to run with two muffin fans to cool the tubess and
>>> operating
>>> CW contests?
>>>
>>> Thoughts?
>>>
>>> -Rex-
>>>
>>> Rex Lint, Consultant
>>> 26 Brek Drive
>>> Merrimack, NH 03054
>>> PH: 603-860-7651
>>>
>>>
>>> _______________________________________________
>>> Amps mailing list
>>> Amps@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/amps
>>>
>>>
>>>
>> No virus found in this incoming message.
>> Checked by AVG - www.avg.com
>> Version: 9.0.733 / Virus Database: 271.1.1/2743 - Release Date: 03/13/10
>> 02:33:00
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com
> Version: 9.0.790 / Virus Database: 271.1.1/2746 - Release Date: 03/14/10
> 03:33:00
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|