Amps
[Top] [All Lists]

Re: [Amps] 4-250A testing

To: <amps@contesting.com>
Subject: Re: [Amps] 4-250A testing
From: "Barrie Smith" <barrie@centric.net>
Date: Mon, 27 Sep 2010 18:56:33 -0600
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Carl:

I've often wondered if the finned anodes had greater plate dissapation than 
the anodes without fins.

I have a variety of old Eimac glass tubes here, some with finned anodes, and 
some without.  An example would be 100TH/TL.

Is it your opinion that the finned anodes would have greater dissapation 
than the unfinned anodes, even though they are all rated the same as far as 
dissapation?

73, Barrie, W7ALW

----- Original Message ----- 
From: "Carl" <km1h@jeremy.mv.com>
To: <TexasRF@aol.com>; <rj3819@yahoo.com>; <amps@contesting.com>
Sent: Monday, September 27, 2010 2:52 PM
Subject: Re: [Amps] 4-250A testing


> The tube has a 5V @ 14.5A filament so Im not sure what you mean by 6.3V @
> 8A?
>
> The only difference between it and a 4-400 is the added fins on the anode
>
> Carl
> KM1H
>
>
> ----- Original Message ----- 
> From: <TexasRF@aol.com>
> To: <rj3819@yahoo.com>; <amps@contesting.com>
> Sent: Monday, September 27, 2010 4:32 PM
> Subject: Re: [Amps] 4-250A testing
>
>
>> To test for emission, it would seem that the grid voltage would need to 
>> be
>> zero or even positive to simulate the effect of the peak driving voltage.
>>
>> If the emission is normal this would cause a very high cathode current,
>> maybe too high if left for more than a few milliseconds. So, some kind of
>> pulse  test would be safer and less stressful on the tube.
>>
>> Emission can appear normal until the cathode current reaches a level of
>> saturation. If this happens at a level too low, then we call that weak
>> emission.  A tube characteristic chart will show these currents and can 
>> be
>> used to
>> evaluate  cathode emission.
>>
>> Use of AC on the screen and plate will certainly allow a pulse test of
>> sorts. You might try the test with no grid voltage and see how that 
>> plays.
>> The
>> lower voltage you are using seems a good idea as well.
>>
>> Also, the AC cycle needs to be in the same phase for both the screen and
>> plate. Otherwise peak plate voltage will happen when there is reverse
>> polarity  on the screen and visa versa. High positive screen voltage with
>> no or
>> reverse  plate voltage is not good for the screen as it will try to 
>> accept
>> all
>> of the  electrons emitted from the cathode and that can be a bunch.
>>
>> This is a very interesting subject and I hope you test further and let us
>> know what you discover.
>>
>> 73,
>> Gerald K5GW
>>
>>
>>
>>
>> In a message dated 9/27/2010 3:11:23 P.M. Central Daylight Time,
>> rj3819@yahoo.com writes:
>>
>> This  tube is on ebay ..
>> Worried about getting an older gassy tube .
>> The  seller states ..
>>
>>
>> This auction is for One 4-250 / 5D22 Transmitting  Tube.  The  labeling 
>> on
>> this
>> tube has been worn other than the  tube number that you  can see in the
>> pics. I
>> am not sure of the  manufacturer, but I am quite  sure that it is either
>> Eimac or
>> Amperex. The visible labeling on the  tube  reads:
>> JAN-CIM-5D22
>> Made In USA
>> There is a stamp inside the tube also  that reads:
>> Q8-9034.
>> This tube is tested for emission from a High  Voltage Transformer:
>> 460 VAC through a 15K @ 10 watt resistor to  screen
>> 920 VAC to plate
>> 6.3VAC @ 8 amps to filament
>> -40 VDC to  grid
>> This tube tested at 200 MA.
>>
>> I have no idea about testing and if  that is good to determine tube
>> emission or
>> not.
>>
>> I have one already  and thought I could have a pair for spare tubes for 
>> my
>> 4-400A amp ? I know  .. not exactly the same .. is just plate dissipation
>> the biggest diff?  would Be able to use them as a lower power set of 
>> spare
>> tubes? or just make  another amp with these?
>>
>> I hope replies go to me as well as the list as  the auction will be over
>> in
>> 4
>> hours..
>>
>> Randy -  N2CUA
>>
>>
>>
>>
>> _______________________________________________
>> Amps mailing  list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
> 



_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>