Re: [Amps] Prefab Cabinets

[n8de@thepoint.net]

If anyone is interested, I have FIVE ..Viking I ... transmitters in my  
pole barn.

Might make a good restoration project ... or, as Bill says, a nice box  
for an amp.

73
Don
N8DE


Quoting "Fuqua, Bill L" <wlfuqu00@uky.edu>:

> viking I or II is interesting.
>    Would be great for a small amplifier for around 500 watts PEP output.
> The plate tank circuit is designed for 400watts PEP output. 1200 or   
> so peak DC plate voltage.
> If you found a scrap one with the plate tanke could make a good pair  
>  572B or 4x  811A amp.
> 73
> Bill wa4lav
>
> ________________________________________
> From: amps-bounces@contesting.com [amps-bounces@contesting.com] On   
> Behalf Of n8de@thepoint.net [n8de@thepoint.net]
> Sent: Monday, February 14, 2011 3:58 PM
> To: Mel
> Cc: Amps@contesting.com
> Subject: Re: [Amps] Prefab Cabinets
>
> Have you considered using a cabinet of the type used for older model
> ham transmitters/receivers?
>
> For example:
> Johnson Viking I/II
> Collins 75A/2/3/4
>
> There are hundreds of these things out there .. some in JUNK condition
> .. that could be repainted/restored .. and would serve your purpose
> quite well.
>
> 73
> Don
> N8DE
>
>
> Quoting Mel <itz_da_police@yahoo.com>:
>
>> Where can a fellow find a chassis to house a bunch of components to
>> assemble a multi-band single hole amplifier.
>>
>> <a
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=DCP01030.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_DCP01030.jpg"; 
>> border="0" alt="Photobucket" ></a>  <a 
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=IMG_20110209_210948.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_IMG_20110209_210948.jpg";
>>  border="0" alt="Photobucket" ></a>  <a 
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=IMG_20110209_211007.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_IMG_20110209_211007.jpg";
>>  border="0" alt="Photobucket" ></a>  <a 
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=DCP01035.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_DCP01035.jpg"; 
>> border="0" alt="Photobucket"   
>> ></a>
>> <a
>>
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=DCP01038.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_DCP01038.jpg"; 
>> border="0" alt="Photobucket" ></a>  <a 
>> href="http://s111.photobucket.com/albums/n150/Paws264/?action=view¤t=DCP01039.jpg";
>>  target="_blank"><img 
>> src="http://i111.photobucket.com/albums/n150/Paws264/th_DCP01039.jpg"; 
>> border="0"   
>> alt="Photobucket"
>> ></a>
>>
>> So, I have every thing that I need, just need something / someway of
>>  housing it so that my conscientious critics are stifled.  I do not
>> want to go the "make-your-own-with-angle-and-pop rivets" route.
>>
>> Frontal dimentions are about 17 inches long (5.0 inchs + another 12
>> inches for the Tank circuit mounting chassis, relays, switches ,
>> etc.) and about 14 inches high.  Have not figured depth yet as the
>> Blower location gas not been finalized (bottow or rear of tube
>> chassis).
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>



_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps