Hi Tom,
your qoutes, puzzles me.
Are we not talking about amps here ?
Obviously, you are telling us more about yourself then we want to know!
As Albert Einsten said:
"A man should look for what is, and not for what he thinks should be"
73's Nermin S58DX
.
----- Original Message -----
From: "Tom Horton" <k5iid@sbcglobal.net>
To: <amps@contesting.com>; "Bob Henderson" <bob@5b4agn.net>
Sent: Tuesday, May 01, 2012 5:06 PM
Subject: Re: [Amps] AL811H metering
Bob,
I haven't had any caps blow or any problems but I find the same type of
tuning characteristics with my 2 month old AL-811 (plain). I am very curious
to hear any comments myself.
Tom K5IID
"Socialism is a philosophy of failure,
the creed of ignorance, and the gospel of envy,
its inherent virtue is the equal sharing of misery.."
-- Winston Churchill
"Democracy depends on well-informed voters; absent that, it is all mud
flowing down hill."
--Charles Harpole
"Luck is a dividend of sweat. The more you sweat, the luckier you get."
If you don't like my signature, well, I am sorry. But I will use it because
it is what I believe.
K5IID Tom Horton Hillsboro, TX
E sorter for ARRL W5 bureau
Same call for 55 years!
--- On Tue, 5/1/12, Bob Henderson <bob@5b4agn.net> wrote:
From: Bob Henderson <bob@5b4agn.net>
Subject: [Amps] AL811H metering
To: amps@contesting.com
Date: Tuesday, May 1, 2012, 3:17 AM
Advice please from AL811H users.
I find myself in temporary possession of an Ameritron AL811H. The amp
belongs to a local friend who purchased it new from DX Engineering at the
end of February this year. I am told that during initial use the amp
seemed fine except, "It didn't seem to tune as expected". A few days
later, while the amp was on stand-by, it emitted a loud bang and died. As
a consequence, I was invited to see if I could identify the problem.
Removal of the case lid revealed one disintegrated and one very blackened
anode blocking capacitor. As the amp had been on stand-by at the time of
the incident, I suspect an infant mortality failure. I called DX
Engineering and the man I spoke to concurred then suggested I contact
Ameritron for replacement parts. I discussed the issue with the Ameritron
technician who agreed to send me two replacement caps. These are now
fitted and the amp once again works. The residual problem is the metering
doesn't behave as expected when the amp is being tuned.
>From 160-40m it behaves largely as expected in that the anode current meter
dips at resonance. Above 40m anode current increases at resonance rather
than dipping. My first thought was instability but the output is clean
with no sign of anything untoward up to 1.5GHz. My second thought was RF
influencing the measuring circuitry but the curious metering behaviour is
equally evident even when the amp is driven with 5W producing just 50W out,
so that seems unlikely.
I currently wonder whether the behaviour I describe is typical of the
AL811H or whether this one might have a wiring error in the metering
circuitry?
Thanks.
Bob, 5B4AGN
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|