## Some of the kenwood xcvrs have no provision for a PO control.
Some of these amps require very little drive power. But a 3-6 db pad on
the
input side of the amps tr relay would help a lot. So the pad is not in the
RX path.
Dunno if the SGC SS amp has overload circuitry in there, so if its
overdriven, it kicks
itself offline?
## On my yaesu FT-1000 MK-V, 200 watt version, there is 3 x power options
in the menu.
10w, 75w, 200w. In the alignment manual, there are 3 x pots to tweak for
those 3 x po levels.
And each pot can be tweaked from 0-200w. So if the amp required say 100w
to drive it,
the 75w setting can be used..and tweaked for 100w. Problem solved.
## Another possible option is he could, if possible, adjust the internal po
control on his kenwood,
and turn it way down. Ur right though, this is not rocket science, and all
sorts of options could be used.
Jim VE7RF
-----Original Message-----
From: Jim W7RY
Sent: Thursday, January 28, 2016 5:32 PM
To: Jim Thomson ; amps@contesting.com
Subject: Re: [Amps] SG-500 ALC Interface to Kenwood TS-480HX
Why not just adjust the power output control on the front of the radio? Or
does the radio have ALC overshoot.. I don’t the the TS-480 has this
problem...
This isn't rocket surgery!
73
Jim W7RY
-----Original Message-----
From: Jim Thomson
Sent: Wednesday, January 27, 2016 5:39 PM
To: amps@contesting.com
Subject: [Amps] SG-500 ALC Interface to Kenwood TS-480HX
Date: Mon, 25 Jan 2016 18:19:13 -0500
From: Ron Youvan <ka4inm@gmail.com>
To: amps <amps@contesting.com>
Subject: Re: [Amps] SG-500 ALC Interface to Kenwood TS-480HX
Larry Dighera wrote:
Given the SG-500's ALC control signal is +1 to +5 VDC, and the Kenwood
TS-480HX's ALC signal expects -7VDC, how have others interfaced these two
pieces of equipment?
I don't know, but a 9 Volt battery might do it.
--
Ron KA4INM - Youvan's corollary:
Every action results in unwanted side effects.
## A 9 vdc battery fed across the far ends of a 50k pot. Then take the
output, between
wiper and positive end of pot. Then you can vary the output of the mess
from 0-9 vdc,
and its all negative Vdc..then feed that negative 0-9 vdc into your TS-
480 HX ALC jack.
Then NO alc connection from xcvr to amp.
## Then you can set the PO of the TS-480HX.....if it has an adjustable PO
to what ever the
amp requires. Then dial up the pot till po of the amp just drops a tiny
bit. At that point, you can
scream all you want..and never over drive the AMP. You can also turn the
PO on the xcvr to max,
and tweak the pot for desired drive into the amp. Same deal, scream all u
want, and u cant overdrive the amp.
## this 2nd scenario works better, since there is no time lag in developing
ALC voltage in the xcvr. You have already
developed it via the 9 vdc battery and pot. The only drawback to using
the 9 vdc battery + pot is..... if you whisper into
mic you will have reduced po from the xcvr. In normal operation it works
superb.
## an alternate method that may well work is to use a SS DC to DC
converter. Then you could feed the +1 to +5 vdc
from the amp.... into the input of the DC to DC converter, the output side
will be either 0-5 vdc positive..OR 0-5 vdc
negative. The dc to dc converter isolates the input to the output side.
In your case, the output side will have its positive
bonded to chassis of xcvr, with negative going to alc jack of xcvr.
Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|