[Top] [All Lists]

Re: [Amps] HF2500 - 15 meter problem

To: Steve London <>, <>
Subject: Re: [Amps] HF2500 - 15 meter problem
From: gudguyham--- via Amps <>
Reply-to: "" <>
Date: Thu, 25 Aug 2022 01:23:44 +0000 (UTC)
List-post: <>
Steve, can you take a digital of the entire RF deck area of that amp and post 
it or send it direct to me?  I don’t think I ever saw that particular 
configuration.  Would that possibly be the later Palstar model?

Sent from the all new AOL app for iOS

On Wednesday, August 24, 2022, 9:08 PM, Steve London <> wrote:

It's a Command Technologies, HF-2500M.
The way they have the 3CPX800's mounted, there isn't room for the RFParts choke 
without some modifications
73,Steve, N2IC

On Wed, Aug 24, 2022 at 7:04 PM <> wrote:

Wow, I’ve seen my share of these amps but never saw that happen to a plate 
choke.  I’m just thinking.  I think I wrongly assumed tnis was a Command Tech 
2500 but apparently is a QRO Tech 2500.  Guys, please, when you ask about 
HF2500’s  mention if it’s a Command or a QRO Technology.  Thanks

Sent from the all new AOL app for iOS

On Wednesday, August 24, 2022, 8:35 PM, Steve London <> wrote:

Well, it looks like it really is the plate choke. It became obvious with
the last test.

Where do I get a new plate choke, or at least a new delrin form to wind my
own ?

Previously, I looked at currently manufactured 3CX800 amps and their plate
chokes are too large to fit. I may go back to that idea and see what I can

Steve, N2IC

On Wed, Aug 24, 2022 at 6:24 PM <> wrote:

> Steve, most of the problems with the tank circuit is from having the
> 40-160m L2 toroid burning up.  I’ve got an HF2500 in my shop right now with
> a melted down L2 toroid.  There is a VERY NARROW group of possibilities
> that can be causing your problem. You’ve done some good detective work so
> far and it seems you’ve covered some good  possibilities.  You said you
> checked the connections to the band switch and to the coil.  Obviously if
> the tap going from bandswitch to L1 is bad on either side you would be
> loosing the tank circuit.  But you checked that already and I assume
> accurately.  So if your troubleshooting is accurate I can only think of one
> last thing that could be wrong.
> CHECK THE PLATES ON THE LOAD CAP!!  The arcing you heard  may have bubbled
> a plate or plates on the load cap and when the load cap is in the resonant
> area for 15 meters the rotor plate may be shorting to the stator plate.
> Use a high power flashlight and inspect the load and tune caps for any
> interference throughout the rotation of the plates when in the 15 meter
> range.  I assume you checked the plate choke already and I also assume you
> are using a dummy load to rule out an antenna problem.  Lou
> Sent from the all new AOL app for iOS
> <>
> On Wednesday, August 24, 2022, 6:51 PM, Steve London <>
> wrote:
> I have a HF2500 with a pair of 3CPX800's. It's been a great amp.
> Up until now, it's had a minor issue. The tuning/loading drifts of 15
> meters as it heats up. Not a big deal - just a small tweak of the tuning
> brings it back to full power. No issue with any other band.
> Today, while operating, it went dead on 15. Suddenly, only a few watts
> output. No drama, bangs, etc. 30 mA grid current, 750 mA plate current.
> Tweaking the tuning made no difference, until it was way out of normal,
> when it increased to 250 watts and something arc'd. All other bands are
> fine.
> Here's what I did, so far:
> - Examined the band switch and contact to the 15 meter tap on the coil.
> Looked good and measured good with an ohm meter.
> - Examined the tuned input network. No obvious problem. Placed a 47 ohm
> resistor across the output of the input network, instead of the tubes. SWR
> and Z looked nominal on all bands.
> - Bypassed the input network, driving the tubes directly. Still bad on 15
> meters. All other bands are good.
> So, that eliminates the input network as the problem.
> What am I missing on the PA or Pi-L side that would only affect 15 meters ?
> 73,
> Steve, N2IC
> _______________________________________________
> Amps mailing list
Amps mailing list

Amps mailing list
<Prev in Thread] Current Thread [Next in Thread>