See: http://ncjweb.com/features/mayjun12feat.pdf
That is the system I have been using here since the Winter of 2011,
designed based on requirements for lowband contesting, et.al.
It can handle up to 128 physical antennas to (4) four receivers, which
in turn are defined as "virtual" antennas in the switching software as
needed. Example, an 8-circle BSEF array is (1) one physical antenna,
but defined as (8) eight separate virtual antennas. A single physical
antenna can also be defined as a separate virtual antenna for each
band. Each antenna can also be split between receivers, up to 4 ways.
*** Unused antennas can be user-selectably terminated to open / ground /
or system impedance, so quite easy to integrate into a reversible bev
system or dual direction vertical arrays that need terminated lines
The switching units are controlled via an RS-485 serial buss, which
allows great distances, and uses a simple ASCII protocol. Therefore,
anyone could spin up software to control it and implement any number of
features (my boxes having scanning capability with ability to select
which antennas to incl in scanning, tracking where two different
antennas are in sync with regard to direction, ie. 8-circle following
bev selection for diversity) . I currently use desktop controllers w/
microprocessors that store the antenna definitions, etc., and "talk" to
the switching units, located 600ft from the shack. There are also
remote control units with outputs to control circular arrays, switchable
antennas or other equipment.
In addition, I use signal processing boxes for each receiver line, which
include preamp, attenuation, TX muting, BCB/bandpass filtering, and
auxiliary switching blocks. All these functions are controlled via the
data buss, so each "virtual" antenna can have it's own gain settings or
things like filtering, AUX switching, etc., controlled on-the-fly from
the dekstop controllers. The processors also monitor the data lines for
any antenna splitting, and compensate for splitter losses automatically
by dialing in more gain (or less ATT). The AUX routing ports are great
for connecting things like NCC-1 phasing units, LF/MF transverters, or
any external processing equipment (similar to Elecraft K3 RX IN / RX OUT
ports). Bandpass filtering is done via W3NQN style receiver filters that
I designed on T-80 cores. There is also RX overload protection using a
COR circuit.
It's quite an easy and obviously extremely flexible system to implement
from a user standpoint, but currently lacks professional enclosures and
a nice software interface. Otherwise, it would fit almost any RX needs
that I can think of (can even be scaled to M/M).
Anyways... maybe with enough interest it could be something I could get
motivated to make available.
73 Eric NO3M
On 01/14/2015 11:56 AM, Herbert Schoenbohm wrote:
I use here a retired Dynair 12X1 passive video switcher. One nice
feature is that each unused RG-6 cable which runs to reversible two
wire Beverages is terminated. With feed line length equal to 1/2 wave
(includes the cable velocity factor.) the 75 ohm termination appears
at the unused port at the feed box. The only down side is that the
push buttons move a connection on a long bus inside and take a finger
pressure. It would be great if someone would market a desk top remote
with momentary light touch switch or with a computer interface. I
have several Ameritron 8X1 along with the RCS 12 but that only gives
me 8 positions. it also does not terminate the unused ports. The
DX-Engineering 8X1, (RR-8B) which can be driven by the desktop RCS-12
has provisions for unused port termination, but to use a 5KW switch
for a bunch of Beverages seems a git of a over-kill. Hopefully
something will be on the market soon as there seems top be a need for
something that will control many Beverage inputs.
Herb Schoenbohm, KV4FZ
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
|