CT-User
[Top] [All Lists]

[ct-user] 9.36-7 bandmap and callouts bugs - help please!

To: <ct-user@contesting.com>
Subject: [ct-user] 9.36-7 bandmap and callouts bugs - help please!
From: Scott Porter & Ann Chase" <n1sp@adam.cheshire.net (Scott Porter & Ann Chase)
Date: Mon, 29 Jun 1998 10:16:48 -0400
Hi All-
I just ran 9.37 in FD from my campsite in Maine, using an icom 725 and ct v
9.37. The bug described below did not occur. I was using a pentium laptop. I
brought home the laptop, radio interface and cable and tried them connected
to my 735 at home and the bug was back . Either my 735 has a problem or CT
does.... the 735 radio interface works fine on either computer with either
of my radios using either interface with CT version 9.35 and lower, but both
9.36 and 9.37 react as described below using the 735 with any combo of
computer and either of my two jcom radio interfaces. And the same hardware
works with CT v 9.37 and my icom 725....
Does anyone have a clue how to get the 735 working again with v 937? the 735
works fine with other programs... and with CT 9.35 and below.

Thanks. 73 Scott N1SP
-----Original Message-----
From: Ken Wolff <kwolff@ultranet.com>
To: Scott Porter & Ann Chase <n1sp@adam.cheshire.net>
To: <ct-user@contesting.com>
Date: Thursday, March 26, 1998 8:05 PM
Subject: Re: [ct-user] Fw: 936 bandmap and callouts bugs


>This may be a problem with sending to the radio too quickly. Can you type
>in a frequency and have the radio go to the correct place?
>
>- Ken
>
>At 03:43 PM 3/26/98 -0500, you wrote:
>>Hi all,
>>I'm having a radio control problem with 936...
>>I've tried both releases of 936 with cold boots....
>>
>>Just downloaded 936 again, some of the buggy stuff I've seen in 9.3x is
>>gone, the
>>jumping freqs while tuning past the highest spotted freq etc.
>>
>>But when I go to either the packetcluster callouts window or the bandmap
>>window and scroll up or down, the frequency comes up fine in the message
"On
>>Spot Freq: " but the radio goes a couple hundered kc higher, out of band
>>even....ie:
>>when trying to jump to 14204.5 in the bandmap from 14177.0 the radio goes
to
>>14394.0
>>I then have to manually tune the radio down to get back in the band before
I
>>can jump again.
>>when trying to jump from 14172.0 to 14196.3 in the callouts window the
radio
>>goes to 143-6.3 (yes a dash!)
>>from 14190.0 to 14243.0 in callouts radio goes to 143-3.0
>>14218.0 to 14204.5 in callout > 143c4.5
>>14326.0 to 14176.0 in callouts >143-6.0
>>14204.0 to 21282.9 in callout> 21402.0
>>21402.0 to 21007.3 in callouts >213-7.0
>>
>>from 21392.0 to 21282.9 in bandmap to 21392.9
>>from 14336.6 to 14196.3 in bandmap to 14486.3
>>from 14161.0 to 14212.0 in bandmap to 143-2.0
>>
>>radio is a icom 735 and no changes to interface or computer  (a 386 dx 25)
>>all works fb in prior versions...
>>Hope someone has some ideas....
>>73 Scott
>>
>>
>>
>>--
>>Submissions:              ct-user@contesting.com
>>Administrative requests:  ct-user-REQUEST@contesting.com
>>WWW:                      http://www.contesting.com/ct/
>>Questions:                owner-ct-user@contesting.com
>>
>>
>Ken Wolff <kwolff@ultranet.com>
>


--
Submissions:              ct-user@contesting.com
Administrative requests:  ct-user-REQUEST@contesting.com
WWW:                      http://www.contesting.com/ct/
Questions:                owner-ct-user@contesting.com


<Prev in Thread] Current Thread [Next in Thread>
  • [ct-user] 9.36-7 bandmap and callouts bugs - help please!, <n1sp@adam.cheshire.net (Scott Porter & Ann Chase) <=