If he can't figure out how to get himself off, I would just set up a filter
& ignore him. If he can't help himself and you have tried I don't know what
else you can do.
At 09:05 PM 5/8/2005, Tom Norris wrote:
>This fellow keeps sending me direct emails asking
>to remove him from the list. Can anyone help him?
>
>I've already suggested he follow the directions
>at the top of each list mail.
>
>73
>
>Tom NU4G
>
>Begin forwarded message:
>
> > From: "huffew@myway.com" <huffew@myway.com>
> > Date: May 8, 2005 7:53:03 PM CDT
> > To: r390a@bellsouth.net
> > Subject: Re: [RTTY] Rigblaster- worth the money?
> > Reply-To: huffew@myway.com
> >
> >
> >
> > please remove me from your mailing list
> >
> >
> >
> >
> > --- On Sun 05/08, Tom Norris < r390a@bellsouth.net > wrote:
> > From: Tom Norris [mailto: r390a@bellsouth.net]
> > To: huffew@myway.com
> > Date: Sun, 8 May 2005 13:20:35 -0500
> > Subject: Re: [RTTY] Rigblaster- worth the money?
> >
> > It's not my mailing list.<br><br>At the top of each RTTY list
> > message are instructions<br>on how to
> > unsubscribe.<br><br><br><br>On May 8, 2005, at 9:45 AM,
> > huffew@myway.com wrote:<br><br>><br>> please remove me from your
> > mailing list<br>><br>><br>><br>><br>> --- On Sat 05/07, Tom Norris
> > < r390a@bellsouth.net > wrote:<br>> From: Tom Norris [mailto:
> > r390a@bellsouth.net]<br>> To: rtty@contesting.com<br>> Date: Sat, 7
> > May 2005 11:42:21 -0500<br>> Subject: Re: [RTTY] Rigblaster- worth
> > the money?<br>><br>> Bill and the group.<br><br>I use a Signal Link
> > SL-1+<br><br>Not <br>> only did it cost less, but it doesn't use
> > up a com port.<br>It has <br>> it's own "vox" circuit built in,
> > just connect to your<br>rig, hook <br>> up audio in/out, and
> > you're ready to go.<br><br>As for homebrew, <br>> the circuit is
> > very simple for this and<br>any of the other <br>> interfaces.
> > Couple of small transformers<br>to isolate audio, an <br>>
> > optoisolator if you are using a comm port<br>to
> > provide TX, if not <br>> a small audio amp ckt to detect tone
> > and<br>turn on a transistor <br>> switch.<br><br>73<br><br>Tom
> > NU4G<br><br>> My main interest with a <br>> rigblaster or similar
> > interface is the fact <br>> that you<br>> <br>> can have multiple
> > features in one box. The way my setup is now, I <br>> can<br>>
> > either use CAT or digital modes, but not both. Lack of <br>>
> > ports and <br>> such are<br>> keeping me from using rig control
> > <br>> while going digital. I have <br>> tried several<br>> <br>>
> > configurations and none seem to work as of yet. And yes, my CI-V
> > <br>> <br>> unit is<br>><br>>
> > homebrew.<br>><br>_______________________________________________<br>R
> > <br>> TTY mailing list<br>RTTY@contesting.com<br>http:// <br>>
> > lists.contesting.com/mailman/listinfo/rtty<br><br>><br>>
> > _______________________________________________<br>> No banners. No
> > pop-ups. No kidding.<br>> Make My Way your home on the Web -
> > http://www.myway.com<br>><br>><br>><br><br>
> >
> > _______________________________________________
> > No banners. No pop-ups. No kidding.
> > Make My Way your home on the Web - http://www.myway.com
> >
> >
> >
>
>_______________________________________________
>RTTY mailing list
>RTTY@contesting.com
>http://lists.contesting.com/mailman/listinfo/rtty
Jim Rhodes K0XU
jim@rhodesend.net
Experience is the thing you have left when everything else is gone.
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty
|