SD-User
[Top] [All Lists]

Re: [SD-User] SD-User Digest, Vol 63, Issue 8

To: sd-user@contesting.com
Subject: Re: [SD-User] SD-User Digest, Vol 63, Issue 8
From: John Muzyka <g4rcg@yahoo.co.uk>
Date: Tue, 18 Mar 2008 19:45:10 +0000 (GMT)
List-post: <sd-user@contesting.com">mailto:sd-user@contesting.com>
I tried what Ian has said, and my winkey (dont know which version but its about 
3-4 years old) on Com3 works fine no irregular speed ups or down and the speed 
pot works fine as well, using SD V13.41B
  Cheers
  John G4RCG

sd-user-request@contesting.com wrote:
  Send SD-User mailing list submissions to
sd-user@contesting.com

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/sd-user
or, via email, send a message with subject or body 'help' to
sd-user-request@contesting.com

You can reach the person managing the list at
sd-user-owner@contesting.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of SD-User digest..."


Today's Topics:

1. PROBLEM WITH WINKEY & V13.41a (IanSDavies@aol.com)


----------------------------------------------------------------------

Message: 1
Date: Mon, 17 Mar 2008 17:54:59 EDT
From: IanSDavies@aol.com
Subject: [SD-User] PROBLEM WITH WINKEY & V13.41a
To: sd-user@contesting.com
Message-ID: 
Content-Type: text/plain; charset="US-ASCII"

Right Paul... here goes:

Only applies to 13.41a and not 13.25 being used as my comparison.

Only occurs when a call is entered in the logging line

Winkey is version V2

using 9 pin serial port as COM1

When a call is on the logging line and the pot is set low speed and I press 
F5, which is #R, the first call is at the correct speed but the second press 
of F5 will result in the speed going up to approximately 28 wpm and sticks 
there for F5 and for all F numbers above. As F6 is my run message this is 
awkward


When it has gone up to 28wpm I can slow it down again with the pot as the 
msge is being sent but the next depression of the key results in the speed 
going 
back up. If in using the pot I go to the lowest point of travel to slow it 
down and I wish to slow down the next msge I can turn the pot up high and then 
down again while sending to bring the speed back down. As before the next 
depression of the key will result in the speed going back up.

I have found that if the F key message is using the call on the logging line 
the speed will stay constant at the speed I set.

Also if I then go back from,say, F2 which has the call in the message to F5 
and with the call still on the logging line I find that the first two #R 
calls have a fast first character and then drops to correct speed. On the third 
or fourth F5 depression the speed shoots up 28wpm and stays there if I carry 
on pressing F5.

I then tried shifting the #R msge to F2 and got the same effect as with F5 
and all the F keys were 'infected' by the higher speed. The only correct speed 
requires the logging line call to be in the message.

The speed indicated on the screen does NOT track the high speed but stays 
indicating the low speed I have set.

I also note that without a call on the logging line the cursor blinks slower 
(and irregularly) compared with having a call entered.

I can't think of any other permutations at present

Ian













------------------------------

_______________________________________________
SD-User mailing list
SD-User@contesting.com
http://lists.contesting.com/mailman/listinfo/sd-user


End of SD-User Digest, Vol 63, Issue 8
**************************************


       
---------------------------------
 Rise to the challenge for Sport Relief with Yahoo! for Good
_______________________________________________
SD-User mailing list
SD-User@contesting.com
http://lists.contesting.com/mailman/listinfo/sd-user

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [SD-User] SD-User Digest, Vol 63, Issue 8, John Muzyka <=