Mike,
A few questions...
- How did you find out that 2E0 was the right address to put in VSEMUIO.CFG ?
- Why is SERIAL 5 PORT ADDRESS = 02E8, instead of 2E0 ?
73,
Steve, N2IC
WG0M@aol.com wrote:
>
> In a message dated 2/12/07 5:53:28 P.M. Central Standard Time,
> ac0w@charter.net writes:
>
> Mike,
>
> See no one responded via the reflector. Did you get the help you need or do
> you still need some help.
>
> If you have the commands all figured out how to start up the program from
> the command prompt, then adding it to the autoexec file is easy.
>
> Bill
> AC0W
>
> Bill:
>
> Got it working, finally thanks to Dan, KD4D. He spent the weekend working
> with me until we had success. He suggested I summarize and publish what I
> had
> to do so others can benefit. I shall.
>
> History:
> My system is W98SE
> I am doing SO2R and decided to run RTTY using MMTTY. However, I needed two
> more Com ports. To solve this issue, I purchased aByterunner 410 H 4
> serial/1lpt card.
>
> Problem: In DOS and running TR, I could not establish rig 2 /computer com
> munication like I had with the card I removed. So, I asked for help.
>
> Dan came to my rescue and spent the better part of this weekend helping me.
>
>
> The below instructions are for the Byterunner 410 H 4 serial/1lpt card. The
> card comes with a disc that contains drivers (including DOS), VSEMUIO setup
> instructions and VSSHOW program that will display port addressing.
>
> The first step is to create a file named VSEMUIO and saved it on the C drive:
> C:\VSEMUIO
> I saved the VESMUIO.EXE (from the supplied cd and VSEMUIO.CFG file (see
> below)
>
> The second step is to set up a cfg file using Notepad. Here is mine:
>
> S,A800,02E0,14,8,5
>
> Save it as VSEMUIO.cfg in the VSEMUIO folder described above. The string
> instructions are detailed in the VSEMUIO Readme file.
>
> The below instructions are what I did to configure COMM 5 to work in DOS
> Third, in TR Two radio config file (some may call it logcfg.dat), I changed
> my rig 2 config line to read
>
> RADIO TWO CONTROL PORT = SERIAL 5 (EXISTING)
>
> SERIAL 5 PORT ADDRESS = 02E8 (NEW)
>
> Reboot into DOS. I hit the F8 key on boot to get me to the command prompt.
> During the boot, you should see the string
> C:\>C:\VSEMUIO\VSEMUIO C:\VSEMUIO\VSEMUIO.CFG
>
> This means the VSEMUIO program is running. At the C prompt start TR the way
> you normally do and enjoy.
>
> I am back to SO2R
>
> So why did I do this? RTTY.........first card only gave me a total of 6 com
> ports.
>
> Com 1 Packet
> Com 2 Rig 1
> Com 3 Keyboad
> Com 4 mouse
> Com 5 Rig 2
> Com 6 Rotor
> Com 7 Rtty rig 1
> Com 8 Rtty rig 2
>
> Dan gave me permission to publish his email address; _kd4d@comcast.net_
> (mailto:kd4d@comcast.net)
>
> I am truly grateful for all the help Dan provided
>
>
>
>
> Michael WG0M
> _______________________________________________
> Trlog mailing list
> Trlog@contesting.com
> http://lists.contesting.com/mailman/listinfo/trlog
>
_______________________________________________
Trlog mailing list
Trlog@contesting.com
http://lists.contesting.com/mailman/listinfo/trlog
|