OOPS!
Just got a follow up mesage.
----- Original Message -----
From: "LDG Electronics, Inc." <ldg@ldgelectronics.com>
To: "Steve Baron - KB3MM" <SteveBaron@starlinx.com>
Sent: January 16, 2001 2:30 AM
Subject: RE: 11MP
> Steve,
>
> Looking back at some of the old pieces of e-mail that I have received on
> this, there is a chance there could be a small amount of noise after each
> transmission on certain frequencies. This is the problem that the one user
> had while operating high speed CW. Since the processor only comes on
during
> transmit, it lags slightly behind the transmitter being un-keyed and some
> noise is present for a few milliseconds on certain frequencies. It just so
> happened that it was right on his net frequency.
>
> We offered a hardware solution for that fellow, but it also disabled the
> auto sensing function as it does not monitor the power during transmit.
>
> There is probably a software fix for this as well that could be
implemented
> for users that wanted to disable the tuner from making any of this noise
> once they have found a spot to operate. Since we have only ever heard of
one
> person having this problem, we did not look at too much. If there are
> others, we should start collecting data and create a solution that is
> useable to all.
>
> Sorry for the confusion of the first e-mail. Our older tuners never shut
off
> and the noise could easily be heard in a receiver. I first thought you
were
> referring to this. The newer units are far better, but still have a chance
> of producing the noise mentioned above.
>
> Dwayne Kincaid
>
> --------------------------------------------
> LDG Electronics, Inc.
> 1445 Parran Road, PO Box 48
> St. Leonard, MD 20685
> Tech Support: 410-586-2177
> Toll Free Order: 1-877-890-3003
> 24 Hour FAX: 410-586-8475
> www.ldgelectronics.com
> --------------------------------------------
>
>
> -----Original Message-----
> From: Steve Baron - KB3MM [mailto:SteveBaron@starlinx.com]
> Sent: Monday, January 15, 2001 8:59 PM
> To: ldg@ldgelectronics.com
> Subject: Re: 11MP
>
>
> Thanks.
>
> Will post that info on the Ten Tev reflector.
>
> ----- Original Message -----
> From: "LDG Electronics, Inc." <ldg@ldgelectronics.com>
> To: "Steve Baron - KB3MM" <SteveBaron@starlinx.com>
> Sent: January 16, 2001 12:58 AM
> Subject: RE: 11MP
>
>
> > AT-11s That are 3 years or older will generate noise on receive. None of
> the
> > newer AT-11s produce any noise on receive. The new ones are AT-11 with
> > version 2.5 PC board or any AT-11MP.
> >
> > Dwayne Kincaid
> >
> > --------------------------------------------
> > LDG Electronics, Inc.
> > 1445 Parran Road, PO Box 48
> > St. Leonard, MD 20685
> > Tech Support: 410-586-2177
> > Toll Free Order: 1-877-890-3003
> > 24 Hour FAX: 410-586-8475
> > www.ldgelectronics.com
> > --------------------------------------------
> >
> >
> > -----Original Message-----
> > From: Steve Baron - KB3MM [mailto:SteveBaron@starlinx.com]
> > Sent: Sunday, January 14, 2001 11:15 PM
> > To: ldg@ldgelectronics.com
> > Subject: 11MP
> >
> >
> > Been thinking about buying one of your kit, but recently saw some
comments
> > on the Ten Tec reflector about noise apparently generanted by your tuner
> and
> > interfering with operation.
> >
> > Is this a possibility ?
> >
> >
> >
>
>
--
FAQ on WWW: http://www.contesting.com/FAQ/tentec
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
|